工厂常见英语
工厂专业英语术语
工厂专业英语术语Assem bly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌O OBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse m achine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet m etal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource depart m en t 人力资源部production depart ment生产部门planning depart m ent企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic m achine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting m achine铆合机position职务president董事长general manager总经理special assistant m anager特助factory director厂长depart m ent director部长deputy m anager | =vice m anager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant m anager助理to m ove, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect m aterial接料to reverse m aterial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load m aterial上料to unload m aterial卸料to return m aterial/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient m anufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良em bedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车com pound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部autom atic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present m embers出席人员subject主题conclusion结论decision item s决议事项responsible depart m ent负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准depart ment部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete m aterial良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw m aterials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flam e cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板m ale die公模fem ale die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜 D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit m aker抽粒机cushion缓冲magnalium镁铝合金m agnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tem po生产进度现状torque扭矩spline=t he multiple keys花键quenchi ng淬火tem pering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。
工厂常见英语词汇
styrofoam chips
barrel
bubble wrap
carton
crate
shipping container
white collar worker
blue collar worker
white collar worker
blue collar worker
usually paid monthly…
How do you call these?
1
2
3
How do you call these?
pressure cleaner
power generator
forklift
…in the shipping department you may need these:
3 2 1
4
5
6
…in the shipping department you may need these:
stairwell / staircase emergency lighting hallway
freight elevator
How do you call
these?
3
4
2
1
5
warehouse
How do you call these?
pallet
shelf/shelves
dolly pallet jack
work boots
hard hat
goggles, eye protection
welder’s mask
reflective vest
1
2
3
4
How do you call these work accessories?
富士康工厂内部常用英语
公司英語-----教育訓練部一:常用術語Hon Hai 鴻海CMM Component module move 機動元件整合CEM Contract Manufaction service 合約委托代工IBSC Internet Business Solution Center 國際互聯網應用中心PCEG Personal Computer Enclosure group個人電腦外設事業群（FOXTEQ）CCBG Connector&cable business groupCPBG Competition business groupESBG Enterprise system business group 鴻富錦事業群SABG system assembly business group 系統組裝事業群NWE Net Work EnclosureNSE Network system enclosureNSG Network system groupNFE Network flexible enclosureFoxcavity = HZ = Hong Zhun 鴻準Stamping tool shop I 沖模一廠Stamping tool shop II 沖模二廠Prototype workshop 樣品中心Steel factory 裁剪廠PCE molding tooling workshop PCE塑模廠Hua Nan test and measurement center 華南檢測中心MPE mobile phone enclosure MPEMBE mobile phone and notebook enclosure 明塑厂MGE Alloy magnesium alloy enclosure 鎂合金Engineer standard 工標Document center (database center)資料中心Design Center 設計中心Painting烤漆(廠) Assembly組裝(廠) Stamping沖壓(廠) Education and Training教育訓練proposal improvement/creative suggestion提案改善Technological exchange and study 技術交流研習會Technology and Development Committee 技術發展委員會BS Brain Storming腦力激蕩QCC Quality Control Circle品質圈PDCA Plan Do Check Action計劃執行檢查總結DCC delivery control center 交貨管制中心3CComputer 電腦類產品Consumer electronics 消費性電子產品Communication 通訊類產品Core value（核心价值）Love 愛心Confidence 信心Decision 決心Corporate culture(公司文化)Integration 融合Responsibility 責任Progress 進步3T STRATEGYTime to market 及時切入生產Time to volume 及時大量生產Time to money 及時大量交貨FOUR CONTROL SYSTEM 四大管制系統Engineering control system 工程管制系統Quality control system品質管制系統Manufacturing control system生產管制系統Management control system經營管制系統7SClassification整理(sorting, organization)-seiriRegulation整頓(arrangement, tidiness)-seitonCleanliness清掃(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教養(discipline)-shitsukeSave 節約Safety安全二:英文縮寫品質人員名稱類QC quality control品質管理人員FQC final quality control終點品質管制人員IPQC in process quality control制程中的品質管制人員OQC output quality control最終出貨品質管制人員IQC incoming quality control進料品質管制人員TQC total quality control全面質量管理PQC passage quality control段檢人員QA quality assurance質量保證人員OQA output quality assurance出貨質量保證人員QE quality engineering品質工程人員品質保證類FAI first article inspection新品首件檢查FAA first article assurance首件確認CP capability index能力指數CPK capability process index模具製程能力參數SSQA standardized supplier quality audit合格供應商品質評估FMEA failure model effectiveness analysis失效模式分析FQC運作類AQL Acceptable Quality Level運作類允收品質水準S/S Sample size抽樣檢驗樣本大小ACC Accept允收REE Reject拒收CR Critical極嚴重的MAJ Major主要的MIN Minor輕微的Q/R/S Quality/Reliability/Service品質/可靠度/服務P/N Part Number料號L/N Lot Number批號AOD Accept On Deviation特采UAI Use As It特采FPIR First Piece Inspection Report 首件檢查報告PPM Percent Per Million百萬分之一制程統計品管專類SPC Statistical Process Control統計製程管制SQC Statistical Quality Control統計品質管制GRR Gauge Reproducibility & Repeatability量具之再制性及重測性判斷量可靠與否DIM Dimension尺寸DIA Diameter直徑N Number樣品數其它品質術語類QIT Quality Improvement Team品質改善組ZD Zero Defect零缺點QI Quality Improvement品質改善QP Quality Policy品质方針TQM Total Quality Management全面品質管理RMA Return Material Audit退料認可7QCTools7 Quality Control Tools品管七大手法通用之件類ECN Engineering Change Notice工程變更通知(供應商) ECO Engineering Change Order工程改動要求(客戶) PCN Process Change Notice工序改動通知PMP Product Management Plan生產管制計劃SIP Standard Inspection Procedure製程檢驗標準程序SOP Standard Operation Procedure製造作業規範IS Inspection Specification成品檢驗規範BOM Bill Of Material物料清單PS Package Specification包裝規範SPEC Specification規格DWG Drawing圖面系統文件類ES Engineering Standard工程標準CGOO China General PCE龍華廠文件IWS International Workman Standard工藝標準ISO International Standard Organization國際標準化組織GS General Specification一般規格部類PMC Production & Material Control生產和物料控制PCC Product control center 生產管制中心PPC Production Plan Control生產計劃控制MC Material Control物料控制DC Document Center資料中心QE Quality Engineering品質工程(部)QA Quality Assurance品質保證(處)QC Quality Control品質管制(課)PD Product Department生產部LAB Laboratory實驗室IE Industrial Engineering工業工程R&D Research & Design設計開發部生產類PCs Pieces個(根,塊等)PRS Pairs雙(對等)CTN Carton卡通箱PAL Pallet/skid棧板PO Purchasing Order采購訂單MO Manufacture Order生產單D/C Date Code生產日期碼ID/C Identification Code(供應商)識別碼SWR Special Work Request特殊工作需求L/N Lot Number批號P/N Part Number料號OEM Original Equipment Manufacture原設備製造PC Personal Computer個人電腦CPU Central Processing Unit中央處理器A.S.A.P As Soon As Possible盡可能快的E-MAIL Electrical-Mail電子郵件N/A Not Applicable不適用QTY Quantity數量I/O input/output輸入/輸出Not Good不行,不合格C=0Critical=0極嚴重不允許APP Approve核準,認可,承認CHK Check確認ASS'Y Assembly裝配,組裝T/P True Position真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance策略品質保證DQA Design Quality Assurance設計品質保證MQA Manufacture Quality Assurance製造品質保證SSQA Sales and service Quality Assurance銷售及服務品質保證LRR Lot Reject Rate批退率SPS Switching power supply電源箱DT Desk Top臥式(機箱)MT Mini-Tower立式(機箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board印刷電路板CAR Correction Action Report改善報告NG Not Good不良WDR Weekly Delivery Requirement周出貨要求PPM Percent Per Million百萬分之一TPM Total Production Maintenance全面生產保養MRP Material Requirement Planning物料需計劃OS Operation System作業系統TBA To Be Assured待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry電子音樂工業Electrical Magnetic Interference 電子干扰RFI Read Frequency Input讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 發光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:專業詞匯通用類president董事長operator作業員position職務general manager總經理special assistant 特deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副課group leader組長line leader線長supervisor 課長responsible department負責單Human Resources Department人力資源部Head count 人頭數production department生產部planning department企劃部QC Section品管課stamping factory沖壓廠painting factory烤漆廠molding factory成型廠administration/general affairs dept./總務部production unit生產單位meeting minutes會議記錄distribution department分發單subject主題conclusion結論decision items決議事項pre-fixed finishing date預定完成Color management 顏色管理Visual management 目視管理production capacity生產力first count初盤first check初盤復櫂second count 復盤second check復盤復核quantity of physical inventory second count 復盤點數量physical inventory盤點數量physical count quantity帳面數difference quantity差異量spare parts physical inventory list備品盤點清單cause analysis原因分析waste materials廢料description品名specification 規格model機種work order工单revision版次remark備注registration登記registration card登記卡to control管制application form for purchase請購consume, consumption消耗to notify通知to fill in填寫to collect, to gather收集statistics統計cosmetic inspection standard 外觀檢驗規範computer case 電腦外殼(組件)personal computer enclosure 電腦機箱產品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上蓋base pan 基座bezel 面板riser card 擴充卡flat cable 排線TOP driver cage 上磁架bottom driver cage 下磁架resin film 樹脂膜raw materials原料materials物料steel plate鋼板roll/coil material捲料spare parts =buffer備品plastic parts塑膠件sheet metal parts/stamping parts 沖件material check list物料檢查表finished product成品semi-finished product半成品good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫packing material包材basket蝴蝶竺plastic basket膠筐flow chart流程表單production tempo生產進度現lots of production生產批量manufacture procedure制程to revise, modify修訂to switch over to, switch—to,switching over切換engineering bottleneck, projectdifficulty工程瓶glove(s)手套glove(s) with exposed fingers割手Band-Aid創可貼Industrial alcohol工業酒精broom掃把mop拖把vacuum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison聯絡單rags抹布lamp holder燈架to mop the floor拖地to clean a table擦桌子air pipe 氣管delivery deadline交貨期die worker模工production, to produce生產equipment設備resistance電阻beacon警示燈coolant冷卻液crusher破碎機club car高爾夫球車plate電鍍power button電源按鍵reset button重置鍵forklift叉車Workshop traveler 天車trailer =long vehicle拖板車Hydraulic trolley手壓車hydraulic hand jack油壓板車casing = containerization裝箱velocity速度patent專利coordinate座標supply and demand供求career card履歷卡barricade隔板carton box紙箱to pull and stretch拉伸work cell/work shop工作間sub-line支線bottleneck 瓶頸模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模stage die工程模compound die復合模shearing die剪邊模riveting die鉚合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 換模to fix a die裝模to repair a die修模punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上墊top plate上托板（頂板）top block上墊腳stripping plate內外打(脫料板) outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板punch沖頭insert入塊(嵌入件)deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖guide plate定位板sliding block滑塊sliding dowel block滑塊固定die locker鎖模器pressure plate =plate pinch壓板thickness gauge厚薄規cutting die, blanking die沖裁die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條panel board鑲塊to load a die裝上模具to unload a die 御模具active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂spring-box eject-plate彈簧箱頂bushing block襯套cover plate蓋板guide pad導料塊pilot導正筒trim剪外邊pierce剪內邊pocket for the punch head挂鉤slug hole廢料孔radius半徑shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺絲form block折刀round pierce punch =die button圓沖子shape punch =die insert異形子stock located block定位塊metal plate鈑金miller銑床grinder磨床tolerance公差score =groove壓線sliding block滑塊lathe車active plate活動板baffle plate擋塊cover plate蓋板groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板capability能力parameter參數factor系數driller鉆床set up die架模height of die setting up架模高度analog-mode device類模器inner guiding post內導柱inner hexagon screw內六角螺dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves =spool等高套pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套press specification沖床規格die height閉模高度flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋self tapping screw自攻螺絲stripper plate脫料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold擠壓式模split mold分割式模具die lifter舉模器top stop上死點bottom stop下死點one stroke一行程to continue, cont.連動to grip(material)吸料location lump, locating piece, locationblock定位塊reset復位to file burr 銼毛刺embedded lump |in'bed| |l mp|鑲塊stamping-missing漏沖to tight a bolt擰緊螺栓to loosen a bolt擰鬆螺栓punched hole沖孔to cut edge =side cut =side scrap 切to bending折彎to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake鉚合designing, to design設計design modification 設計脩改成gauge(or jig)治具pedal踩踏板stopper阻擋器flow board流水板torque扭矩spline =the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速moly high speed steel鉬高速forming成型(抽凸,沖凸)draw hole抽孔bending折彎emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線stamp letter沖字(料號)tick-mark nearside正面壓印tick-mark farside反面壓印extension DWG展開圖procedure DWG工程圖die structure DWG模具結構圖沖壓類punch, press沖punching machine 沖床hydraulic machine油壓機jack升降機decoiler整平機manufacture management製造管理stamping, press沖壓feeder送料機rack, shelf, stack料架taker取料機to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|報廢scrape ..v.刮;削robot機械手production line流水線packaging tool打包機packaging打包成型類well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道welding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleeve套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料guide pin導銷eject rod (bar)（成型機）頂業subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口diaphragm gate隔膜澆口ring gate環形澆口submarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口runner less無澆道sprue less 無射料管方式long nozzle延長噴嘴方式spur澆口;溶waste廢料board看板sliding rack滑料架to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料material change, stock change材料變更feature change 特性變更prepare for, make preparations for 準備rotating speed, revolution轉速abnormal handling異常處理組裝類Assembly line組裝線Layout布置圖Conveyer流水線運輸帶Rivet machine拉釘機Rivet gun拉釘槍Screw driver起子Electric screw driver電動起子Hydraulic machine 液壓機Pneumatic screw driver氣動起automation自動化to stake, staking, riveting鉚合add lubricant oil加潤滑油argon welding氬焊cylinder油缸robot機械手conveying belt輸送帶transmission rack輸送架to draw holes抽孔bolt螺栓nut 螺母screw 螺絲identification tag標示單screwdriver plug起子插座automatic screwdriver自动啟子to move, to carry, to handle搬be put in storage入庫packing包裝staker = riveting machine鉚合fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet/skid棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine/heat stake熱熔機processing, to process加工delivery, to deliver 交貨to return delivery to. to send delivery back to return of goods退easily damaged parts易損件standard parts標準件to lubricate潤滑spring 彈簧spare tools location/buffer手工備品spare molds location模具備品tox machine自鉚機烤漆類phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈organic solvent有機溶劑demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料volatile揮發性degrease脫脂rinse水洗alkaline etch齡咬desmot剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔scraped products報放品disposed products處理品dismantle the die折模auxiliary function輔助功能heater band 加熱片thermocouple熱電偶derusting machine除銹機degate打澆口dryer烘干機induction感應induction light感應光response =reaction =interaction感ram連杆edge finder巡邊器concave凸convex凹cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線grit沙礫granule =pellet =grain細粒sand blasting噴沙grit maker抽粒機cushion緩沖fillet鑲;嵌邊roller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸品質類qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part來件不良exposed metal/bare metal金屬裸露excessive defect過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格cosmetic defect外觀不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑絲missing part漏件wrong part錯件oxidation氧化defective threading抽芽不良poor staking鉚合不良deficient purchase來料不良deficient manufacturing procedure制程不良cosmetic inspection外觀檢查inner parts inspection內部檢查blister 氣泡angular offset 角度偏差dent 壓痕scratch 刮傷deformation 變形filings 鐵削defective label 不良標簽abrasion 磨損Breaking. (be)broken,(be)cracked 斷裂short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delaminating起鱗speckle斑點mildewed =moldy = mouldy發霉deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excessive gap間隙過大grease/oil stains油污inclusion雜質shrinking/shrinkage縮水mixed color雜色fold of packaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬impurity 雜質Mismatch 錯位failure, trouble 故障deformation 變形rust 生銹peel 脫漆Shrink 縮水Contamination 臟污water spots 水漬Gap 間隙label error 標簽錯誤Missing label 漏貼rejection criteria 拒收標准Suspected rejects 可疑庇abrasion 損傷、磨損Texture surface 印花紋表面Streak 條紋stains 污點Blotch 斑點discoloration 脫色Inclusion 雜質slug mark 壓痕dirt grime 灰塵blush 毛邊薄膜sink 下凹Hickey 漏漆labels and logos 貼紙與商標Configuration labels 組合貼紙corrugated container 瓦擺紙箱Delaminating 脫層splattering 散點Gouge 銼孔puckering。
工厂常用英语
工厂常用英语以下是一些工厂常用的英语句子，供您参考：1.This is the material we use to make the product.这是我们制造产品所使用的材料。
2.We have a production line in place to assemble the components.我们有一条生产线用于组装部件。
3.The quality of our products is our top priority.我们最看重产品质量。
4.This machine is used to cut the edges of the sheet material.这台机器是用来切割薄板材料的边缘。
5.The worker uses a die to shape the metal.工人使用模具来成型金属。
6.We need to maintain a clean and safe work environment.我们需要保持一个干净、安全的工作环境。
7.The product must be inspected for defects before shipment.产品在装运前必须经过缺陷检查。
8.We use a computer-numerical-control machine to cut the parts.我们使用数控机床来切割零件。
9.The operator monitors the machines to ensure they are running properly.操作员监视机器的运行状况以确保正常运行。
10.We have a quality control department to ensure our products meet thestandard.我们有一个质量控制部门来确保我们的产品符合标准。
11.This machine is used to drill holes in the metal plate.这台机器是用来在金属板上钻孔的。
工厂常用英语缩写
BYD公司英语一:常用部门术语Document center (database center) 料中心Design Center 设计中心Shang Hai Test & measurement laboratory 上海检测实验室Molding plant 成型车间Painting plant 烤漆车间Assembly plant 组装车间Stamping plant 冲压车间Business center 商务中心Quality Assurance Department 品保部Project Department 项目部Manufacture Department 制造部Tooling center 模具中心Plan Department 计划部Education and Training 教育训练Training room 教育训练室QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品7SClassification整理(sorting, organization)-seiriRegulation整顿(arrangement, tidiness)-seitonCleanliness清扫(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教养(discipline)-shitsukeSave 节约Safety安全二:英文缩写品质人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQM total quality management 全面质量管理QA quality assurance 质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商品质评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REJ Reject 拒收CRI Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 品质/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它品质术语类QIT Quality Improvement Team 品质改善小组ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商) PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 品质工程QA Quality Assurance 品质保证QC Quality Control 质量管理PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱.PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源)DQA Design Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业 Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入AVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类responsible department负责单位Human Resources Department 人力资源部Head count 人头数production department生产部门planning department企划部stamping factory冲压厂painting factory烤漆厂molding factory成型厂production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physicalinventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physicalinventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/goodparts良品defective product/non-goodparts不良品disposed goods处理品warehouse/hub仓库packing material包材plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to,switch—to, switching over切换engineering bottleneck,project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模.progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) upper supporting blank上承板upper padding plate blank 上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block forlocation定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch =stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =diebutton圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车.active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locatingpiece, location block定位块reset复位to file burr 锉毛刺embedded lump |in'bed||l mp|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =sidescrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印extension DWG展开图procedure DWG工程图die structure DWG模具结构图冲压类punch, press冲punching machine 冲床hydraulic machine油压机.jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board看板sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stockchange材料变更feature change 特性变更prepare for, make preparationsfor 准备rotating speed, revolution转速abnormal handling异常处理engineering plastics 工程塑胶 epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetatecopolymer 乙烯-醋酸乙烯EVAethylene-vinlacetatecopolyme 醋酸乙烯共聚物EVAexpanded polystyrene?泡聚苯乙烯EPSfiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrenerigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamineresin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶 polyacrylicacid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate聚对苯二甲酸丁酯PBTpolycarbonate 聚碳酸酯PCpolyethyleneglycol 聚乙二醇PFG.polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯 polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVApolyvinylbutyral 聚乙烯醇缩丁醛PVBpolyvinylchloride 聚氯乙烯PVCpolyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物 silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂acrylic 压克力 casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetatebutyrate 醋酸丁酸纤维素CABcomposite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色 colormasterbatch 色母料compound 混合料 copolymer共聚合体cull 残料废品 cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间 ductility 延性elastomer 弹性体 extrudedbead sealing 压出粒涂层法feed 供料 filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂 gloss光泽granule 颗粒料 gunk 料斗hot mark 热斑 hot stamping烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机 levelingagent 匀涂剂lubricant 润滑剂 matcheddie method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴 oriented film取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂 plunger压料柱塞porosity 孔隙率 post cure後固化premix 预混料 purging 清除reciprocating screw 往复螺杆 resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片 shot 注射shot cycle 射出循环 slipagent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clampingsystem 肘杆式锁模装置torpedo spreader 鱼雷形分流板 transparency 透明性void content 空洞率工程试验与试验用语air permeability test 透气性试验 austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度 brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验 conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验 dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验 environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验 falling ball impact test 落球冲击试验fatigue test 疲劳试验 ferrite 纯铁体.gantt chart 甘特图 heat cycle test 热循环试验histogram 柱状图 hot bend test 热弯试验izod impact test 埃左德冲击试验 loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体 mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验 normal distribution 常态分配ozone resistance test 抗臭氧试验 pareto diagram 柏拉图peeling test 剥离试验 pinhole test 针孔试验机rattler test 磨耗试验 rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度 rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验 sampling inspection 抽样检查scratch hardness 抗刮硬度 shore hardness 萧氏硬度spiral flow test 螺旋流动试验 surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机 tensile impact test 拉伸冲击试验tensile strength 抗拉强度 tension test 张力试验thermal shock test 冷热剧变试验 torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计 vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验 warpage test 翘曲试验weatherometer 人工老化试验机 weissenberg effect 威森伯格回转效应组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting 铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to senddelivery back to return ofgoods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机. 烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴品质类qualified products,up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slipperyslipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturingprocedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking.(be)broken,(be)cracked断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞.speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕。
富士康工厂内部常用英语
公司英語-----教育訓練部一:常用術語Hon Hai 鴻海CMM Component module move 機動元件整合CEM Contract Manufaction service 合約委托代工IBSC Internet Business Solution Center 國際互聯網應用中心PCEG Personal Computer Enclosure group 個人電腦外設事業群（FOXTEQ）CCBG Connector&cable business groupCPBG Competition business groupESBG Enterprise system business group 鴻富錦事業群SABG system assembly business group 系統組裝事業群NWE Net Work EnclosureNSE Network system enclosureNSG Network system groupNFE Network flexible enclosureFoxcavity = HZ = Hong Zhun 鴻準Stamping tool shop I 沖模一廠Stamping tool shop II 沖模二廠Prototype workshop 樣品中心Steel factory 裁剪廠PCE molding tooling workshop PCE塑模廠Hua Nan test and measurement center 華南檢測中心MPE mobile phone enclosure MPEMBE mobile phone and notebook enclosure 明塑厂MGE Alloy magnesium alloy enclosure 鎂合金Engineer standard 工標Document center (database center)資料中心Design Center 設計中心Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練proposal improvement/creative suggestion提案改善Technological exchange and study 技術交流研習會Technology and Development Committee 技術發展委員會BS Brain Storming 腦力激蕩QCC Quality Control Circle 品質圈PDCA Plan Do Check Action 計劃執行檢查總結DCC delivery control center 交貨管制中心3CComputer 電腦類產品Consumer electronics 消費性電子產品Communication 通訊類產品Core value（核心价值）Love 愛心Confidence 信心Decision 決心Corporate culture(公司文化)Integration 融合Responsibility 責任Progress 進步3T STRATEGYTime to market 及時切入生產Time to volume 及時大量生產Time to money 及時大量交貨FOUR CONTROL SYSTEM 四大管制系統Engineering control system 工程管制系統Quality control system品質管制系統Manufacturing control system生產管制系統Management control system經營管制系統7SClassification整理(sorting, organization)-seiriRegulation整頓(arrangement, tidiness)-seitonCleanliness清掃(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教養(discipline)-shitsukeSave 節約Safety安全二:英文縮寫品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理PQC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認CP capability index 能力指數CPK capability process index 模具製程能力參數SSQA standardized supplier quality audit 合格供應商品質評估FMEA failure model effectiveness analysis 失效模式分析FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的Q/R/S Quality/Reliability/Service 品質/可靠度/服務P/N Part Number 料號L/N Lot Number 批號AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件檢查報告PPM Percent Per Million 百萬分之一制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制GRR Gauge Reproducibility & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑N Number 樣品數其它品質術語類QIT Quality Improvement Team 品質改善組ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 品质方針TQM Total Quality Management 全面品質管理RMA Return Material Audit 退料認可7QCTools 7 Quality Control Tools 品管七大手法通用之件類ECN Engineering Change Notice 工程變更通知(供應商) ECO Engineering Change Order 工程改動要求(客戶) PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Standard Inspection Procedure 製程檢驗標準程序SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類ES Engineering Standard 工程標準CGOO China General PCE龍華廠文件IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格部類PMC Production & Material Control 生產和物料控制PCC Product control center 生產管制中心PPC Production Plan Control 生產計劃控制MC Material Control 物料控制DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部生產類PCs Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號OEM Original Equipment Manufacture 原設備製造PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量I/O input/output 輸入/輸出Not Good 不行,不合格C=0 Critical=0 極嚴重不允許APP Approve 核準,認可,承認CHK Check 確認ASS'Y Assembly 裝配,組裝T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率SPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WDR Weekly Delivery Requirement 周出貨要求PPM Percent Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OS Operation System 作業系統TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 電子音樂工業Electrical Magnetic Interference 電子干扰RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 發光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessA VL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable 三:專業詞匯通用類president董事長operator作業員position職務general manager總經理deputy manager |'depjuti| =vice manager副理group leader組長line leader線長supervisor 課長Human Resources Department人力資源部Head count 人頭數planning department企劃部QC Section品管課stamping factory沖壓廠painting factory烤漆廠molding factory成型廠administration/general affairs dept./總務部production unit生產單位meeting minutes會議記錄subject主題conclusion結論decision items決議事項Color management 顏色管理Visual management 目視管理production capacity生產力first count初盤first check初盤復櫂second count 復盤second check復盤復核quantity of physical inventory second count 復盤點數量physical inventory盤點數量difference quantity差異量spare parts physical inventory list備品盤點清單cause analysis原因分析waste materials廢料description品名specification 規格model機種work order工单revision版次remark備注registration登記registration card登記卡to control管制applicationformforpurchaseconsume, consumption消耗to notify通知to fill in填寫to collect, to gather收集statistics統計cosmetic inspection standard 外觀檢驗規範computer case 電腦外殼(組件)personal computer enclosure 電腦機箱產品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上蓋base pan 基座bezel 面板riser card 擴充卡flat cable 排線TOP driver cage 上磁架bottom driver cage 下磁架resin film 樹脂膜raw materials原料materials物料steel plate鋼板roll/coil material捲料spare parts =buffer備品plastic parts塑膠件sheet metal parts/stamping parts 沖件material check list物料檢查表finished product成品semi-finished product半成品good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫packing material包材basket蝴蝶竺plastic basket膠筐flow chart流程表單lots of production生產批量manufacture procedure制程to revise, modify修訂to switch over to, switch—to,switching over切換enineeringbottleneck,projctdifficulty工glove(s)手套glov(s)withexposedfingersBand-Aid創可貼Industrial alcohol工業酒精broom掃把mop拖把vacuum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison聯絡單rags抹布lamp holder燈架to mop the floor拖地to clean a table擦桌子air pipe 氣管delivery deadline交貨期die worker模工production, to produce生產equipment設備resistance電阻beacon警示燈coolant冷卻液crusher破碎機club car高爾夫球車plate電鍍power button電源按鍵reset button重置鍵forklift叉車Workshop traveler 天車trailer =long vehicle拖板車Hydraulic trolley手壓車hydraulic hand jack油壓板車casing = containerization裝箱velocity速度patent專利coordinate座標supply and demand供求career card履歷卡barricade隔板carton box紙箱to pull and stretch拉伸work cell/work shop工作間sub-line支線bottleneck 瓶頸模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模stage die工程模compound die復合模shearing die剪邊模riveting die鉚合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 換模to fix a die裝模to repair a die修模punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板)upper supporting blank上承板top plate上托板（頂板）top block上墊腳stripping plate內外打(脫料板) outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板punch沖頭insert入塊(嵌入件)deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋沖子guide plate定位板sliding block滑塊die locker鎖模器pressure plate =plate pinch壓板thickness gauge厚薄規cuttingdie,blankingdiedie block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條panel board鑲塊to load a die裝上模具to unload a die 御模具active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱bushing block襯套cover plate蓋板guide pad導料塊pilot導正筒trim剪外邊pierce剪內邊slug hole廢料孔radius半徑shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺絲form block折刀round pierce punch =die button圓沖子shape punch =die insert異形子stock located block定位塊metal plate鈑金miller銑床grinder磨床tolerance公差score =groove壓線sliding block滑塊lathe車active plate活動板baffle plate擋塊cover plate蓋板groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板capability能力parameter參數factor系數driller鉆床set up die架模height of die setting up架模高度analog-mode device類模器inner guiding post內導柱dowel pin固定銷coil spring彈簧lifter pin頂料銷pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套press specification沖床規格die height閉模高度flow mark流痕welding mark溶合痕self tapping screw自攻螺絲stripper plate脫料板piston活塞handle mold手持式模具flash mold溢流式模具split mold分割式模具die lifter舉模器top stop上死點bottom stop下死點one stroke一行程to continue, cont.連動to grip(material)吸料location lump, locating piece, locationblock定位塊reset復位to file burr 銼毛刺embedded lump |in'bed| |l mp|鑲塊stamping-missing漏沖to tight a bolt擰緊螺栓to loosen a bolt擰鬆螺栓punched hole沖孔to bending折彎to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake鉚合designing, to design設計design modification 設計脩改成gauge(or jig)治具 pedal 踩踏板 stopper 阻擋器 flow board 流水板 torque 扭矩spline =the multiple keys 花鍵 quenching 淬火 tempering 回火 annealing 退火 carbonization 碳化 alloy 合金forming 成型(抽凸,沖凸) draw hole 抽孔 bending 折彎 emboss 凸點 dome 凸圓semi-shearing 半剪 stamp mark 沖記號 deburr or coin 壓毛邊punch riveting 沖壓鉚合 side stretch 側沖壓平 reel stretch 卷圓壓平 groove 壓線stamp letter 沖字(料號)tick-mark nearside 正面壓印 tick-mark farside 反面壓印 extension DWG 展開圖 procedure DWG 工程圖die structure DWG 模具結構圖沖壓類punch, press 沖punching machine 沖床 hydraulic machine 油壓機 jack 升降機 decoiler 整平機manufacture management 製造管理 stamping, press 沖壓 feeder 送料機rack, shelf, stack 料架 taker 取料機to reverse material 翻料 to load material 上料 to unload material 卸料to return material/stock to 退料scraped |'skr æpid|報廢 scrape ..v.刮;削 robot 機械手production line 流水線 packaging tool 打包機 packaging 打包成型類well type 蓄料井insulated runner 絕緣澆道方式 hot runner 熱澆道 runner plat 澆道模塊 valve gate 閥門澆口band heater 環帶狀的電熱器 spindle 閥針spear head 鉋尖頭 slag well 冷料井 cold slag 冷料渣 air vent 排氣道 welding line 熔合痕 eject pin 頂出針 knock pin 頂出銷return pin 回位銷反頂針 sleeve 套筒stripper plate 脫料板 insert core 放置入子 guide pin 導銷subzero 深冷處理three plate 三極式模具 runner system 澆道系統 stress crack 應力電裂 orientation 定向sprue gate 射料澆口，直澆口 nozzle 射嘴sprue lock pin 料頭鉤銷(拉料杆) slag well 冷料井 side gate 側澆口 edge gate 側緣澆口 tab gate 搭接澆口 film gate 薄膜澆口 flash gate 閘門澆口 slit gate 縫隙澆口 fan gate 扇形澆口 dish gate 因盤形澆口 diaphragm gate 隔膜澆口 ring gate 環形澆口submarine gate 潛入式澆口 tunnel gate 隧道式澆口pin gate 針點澆口 runner less 無澆道sprue less 無射料管方式 long nozzle 延長噴嘴方式 spur 澆口;溶 waste 廢料 board 看板sliding rack 滑料架 to impose lines 壓線to compress, compressing 壓縮 character die 字模 to feed, feeding 送料material change, stock change 材料變更feature change 特性變更prepare for, make preparations for 準備rotating speed, revolution 轉速 abnormal handling 異常處理組裝類Assembly line 組裝線 Layout 布置圖Conveyer 流水線運輸帶 Rivet machine 拉釘機 Rivet gun 拉釘槍 Screw driver 起子Electric screw driver 電動起子 Hydraulic machine 液壓機 P n e automation 自動化 to stake, staking, riveting 鉚合 add lubricant oil 加潤滑油 argon welding 氬焊 cylinder 油缸 robot 機械手conveying belt 輸送帶 transmission rack 輸送架 to draw holes 抽孔 bolt 螺栓 nut 螺母screw 螺絲identification tag 標示單 screwdriver plug 起子插座 automatic screwdriver 自动啟子 be put in storage 入庫 packing 包裝fit together 組裝在一起 fasten 鎖緊(螺絲)fixture 夾具(治具)pallet/skid棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine/heat stake熱熔機processing, to process加工delivery, to deliver 交貨to return delivery to. to send deliverybacktoreturnofgoodeasily damaged parts易損件standard parts標準件to lubricate潤滑spring 彈簧tox machine自鉚機烤漆類phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈organic solvent有機溶劑demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料volatile揮發性degrease脫脂rinse水洗alkaline etch齡咬desmot剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔scraped products報放品disposed products處理品dismantle the die折模auxiliary function輔助功能heater band 加熱片thermocouple熱電偶derusting machine除銹機degate打澆口dryer烘干機induction感應induction light感應光response=reaction=interactioram連杆edge finder巡邊器concave凸convex凹cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線grit沙礫granule =pellet =grain細粒sand blasting噴沙grit maker抽粒機cushion緩沖fillet鑲;嵌邊roller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸品質類qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part來件不良exposed metal/bare metal金屬裸露excessive defect過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格cosmetic defect外觀不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑絲missing part漏件wrong part錯件oxidation氧化defective threading抽芽不良poor staking鉚合不良deficient purchase來料不良deficient manufacturing procedure制程不良cosmetic inspection外觀檢查inner parts inspection內部檢查blister 氣泡angular offset 角度偏差dent 壓痕scratch 刮傷deformation 變形filings 鐵削defective label 不良標簽abrasion 磨損Breaking. (be)broken,(be)cracked 斷裂short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delaminating起鱗speckle斑點mildewed =moldy = mouldy發霉deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excessive gap間隙過大grease/oil stains油污inclusion雜質shrinking/shrinkage縮水mixed color雜色fold of packaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬impurity 雜質Mismatch 錯位failure, trouble 故障deformation 變形rust 生銹peel 脫漆Shrink 縮水Contamination 臟污water spots 水漬Gap 間隙label error 標簽錯誤Missing label 漏貼rejection criteria 拒收標准Suspected rejects 可疑庇abrasion 損傷、磨損Texture surface 印花紋表面Streak 條紋stains 污點Blotch 斑點discoloration 脫色Inclusion 雜質slug mark 壓痕dirt grime 灰塵blush 毛邊薄膜sink 下凹Hickey 漏漆labels and logos 貼紙與商標Configuration labels 組合貼紙corrugated container 瓦擺紙箱Delaminating 脫層splattering 散點Gouge 銼孔puckering。
工厂常用英语词汇一览表
Page:1 of 3常用英文對照表生產規格specification or spec光藕合二極體photo couple生產注意事項S/N突破吸收器varistor料表BOM(bill of material)場效電晶體pet電氣規格ES接地星形墊片lock washer電路圖PK橋片整流bridge diode外觀尺寸圖PD可變電阻VR(variable)零件符號圖PM晶片電阻chip resistor連片圖H-PCB陶瓷電容ceramic capacitance銅箔面布線圖PI保險絲座Fuse holder調整regulation熱敏電阻NTC機種model積體電路IC版本revision彈簧墊片spring washer發行日期issue date星形墊片star washer品名料號p/n二極體diode(dio)說明description電晶體transistor草擬reported by小基板control board審核checked by穩壓器regulator核準approved by電路板PCB生產通知FN(factory notice)濾波器filter工程變更通知ECN(engineering change notice)連接器connector立即變更immediately change輸出線output cable自然切換running change散熱片heat sink舊版本old rev絕緣片insulator新版本new rev電阻resistor(res)圖號drawing no電容capacitor客戶customer線圈choke倉庫warehouse電感inductor人力資源HR human resources齊納zener資料中心document control風扇fan追求卓越excellence外殼case品質至上quality開關switch信賴第一reliability插座socket零件component螺帽nut電氣electrical墊片washer制程process罩框housing線軸bobbin端子terminal束帶cable卯釘rivet螺絲screw套管tube塑膠柱space supportlr標簽label顏色color樹脂epoxy黑色black跳線jumper wirePage:2 of 3藍色blue錫棒solder bar棕色brown膠glue金色gold加工成型pre-forming灰色gray助焊劑flux綠色green插件insertion橙色orange錫燼solder machine紅色red比重gravity銀色silver溫度temperature紫色violet補焊touch-up白色white崩應burn-in黃色yellow組立assemby粉紅色pink包裝packing樣品sample測試test目標target調整adjust踫觸touch報表report方法method接地grounding處置disposition記錄record追蹤follow up產品product分析analysis變更change檢驗inspection修訂revise規格specification or spec重工rework缺點defect儲存storage修復repair更新update篩選sorting增加ADD備注remark刪除cancel正確地correct問題problem進料檢驗IQC治具fixture成品檢驗FQC安全safety流程圖flow chare計劃plan過電壓保護over voltage protection日期date過電流保護over current protection位置location過功率保護over power protection頻率frequency輸出output負載load漣波ripple滿載fun load雜訊noise損壞damage異音noise buzz示波器oscillograph保護protection高壓測試hi-pot test燒機broken品質手冊quality manual電壓voltage品質政策quality policy電流current工作指導書operation instructor注意專心attention允收accept風扇不轉fan no turn功能function研究中under study材料materionPage:3 of 3報警器警戒使警覺alarm參考refer to請求request退貨reject不同different變更依據alteration ref錯誤過失error作業程序procedure百萬分之一 1 ppm極性反polarity reversed最大負載max load漏件missing part電腦computer錯件wrong part控制control壞件component標志marking無線尾no lead protruded制程品質保證PQA裝插不良improper insertion漏電流leakage currem零件偏移component shifted錫solder絕緣不良insulation damaged範圍range成型不良poor preforming棧板pallet錫洞solder void開關電源供應器switch power supply錫多excessive solder高壓hi-pot近似短路near short作業員operator錫裂solder crack主要magor錫渣solder spatter檢查check錫橋solder bridge批lot冷焊cold solder加嚴tightened錫尖solder icicle安全安規safety短路solder short額定的reted錫少solder in sufficient電壓下降drop漏焊missing solder正常標準的normal翹皮peeling off顯示器display漏標示missing marking碟裝tray線腳長lead protrusion out of spec蓋子lid漏點膠missing glue塑膠袋pi bat防焊漆膠落solder mask peeling off紙板pad污損contamination干燥劑dryer當機shut down保護膜pi film誤判NDT隔板partition重調re-adjust單箱carton測試板test board海棉pu foam外殼下蓋lower case保力龍EPS外殼上蓋upper case遙控的remote保險絲fuse判斷不公(錯誤)misjudge選擇開關select switch主席chairman核對check。
电子工厂专业英语词汇
Assembly line组装线Layout 部署图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pworktablen工作桌OOBAe 开箱检查ufit together 组装在一同mfasten 锁紧 (螺丝 )afixture 夹具 (治具 )pallet 栈板ibarcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机crepair 维修operator作业员eQC 品管wsupervisor课长ME 制造工程师dMT 制造生技cosmeticr inspect外观检查inner parts inspect内部检查thumbv screw大头螺丝lbse.inch镑、英寸EMIr gasket导电条气前板front platerear plate后板chassis |'∫ ? si|基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts冲件plastic parts塑料件、冲压、喷漆等专业词汇SOP 制做作业程序material check list物料检查表work cell工作间trolley 台车carton 纸箱sub-line支线left fork叉车Personnel resource department人力资源部planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂punching machine冲床robot 机械手hydraulic machine油压机lathe 车床planer |'plein |刨床miller 铣床grinder 磨床driller 钻床linear cutting线切割electrical sparkle电火花welder电焊机position职务president董事长general manager总经理factory director厂长department director 部长deputy manager |'depjuti|=vice manager 副理section supervisor 课长 deputysection supervisor =vicegroup leader/supervisor 组长line supervisor 线长 assistantmanager 助理be put in storage入库pack packing包装to apply oil擦油to file burr锉毛刺final inspection终检to connect material接料to reverse material翻料wet station沾湿台Tiana 天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid| 报废scrape ..v. 刮 ;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n| 氧化scratch 刮伤dents 压痕defective upsiding down萌芽不良defective to staking铆合不良embeded lump|in'bed| |l mp| 镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改良spare parts=buffer备件forklift 叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt 螺栓name of a department部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规 gauge(or jig) 治具power wire电源线buzzer 蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal践踏板stopper阻拦器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套gthumbl大拇指forefinger食指midfingerv中指ringe finger无名指little(finger小指bands-aid 创可贴industrial)alcohol工业酒精alcohol container沾湿台headw of screwdriver起子头sweeperi扫把tmop 拖把hvacuum cleaner 吸尘器rag抹布garbage container灰箕xgarbage can垃圾箱pgarbage bag垃圾袋ochain 链条sjack 起落机productione line流水线dchain 链条槽magnetizer加磁器flamp holder灯架in to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool 打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺点critical defect 极严重缺点major defect主要缺点minor defect次要缺点not up to standard不合规格dimension/size is a little bigger 尺寸偏大 (小)cosmetic defect 外观不良 slippedscrewhead / slippery screw head螺丝滑头slipped screwhead / shipperyscrew thread 滑手 speckle斑点mildewed=moldy=mouldy 发霉rust 生锈deformation变形burr( 金属 )flash( 塑件 )毛边poor staking铆合不良excessive gap 空隙过大grease/oil stains油污inclusion 杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch 划伤poor processing制程不良poor incoming part事件不良fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍pexposed metal/bare metal 金属裸露lack of painting 烤漆不到位issafety 安全quality 质量delivery deadline交货期cost 成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企划QC 品管die worker模工production, to produce生产equipment设施to start a press 开机stop/switch off a press关机classification 整理regulation整改cleanness打扫conservation洁净culture 修养qualified products, up-to-gradeproducts 良品defective products, not up-to-grade products 不良品waste 废料board 广告牌feeder 送料机sliding rack滑料架defective product box不良品箱die change换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket 蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cutmaterial, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualified, up to grade合格not up to grade, not qualified不合格material change, stock change 资料更改feature change 特征更改evaluation 评估prepare for, make preparationsfor 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异样办理production unit 生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify 订正to switch over to, switch---tothrow--over switching over切换estagen die 工程模automationg自动化ito stake, staking, riveting铆合nadd lubricating oil加润滑油eshut die 架模eshut height of a die架模高度ranalog-mode device类模器die lifter 举模器argon welding氩焊Vocabularyg for stamping冲,压常词汇stamping, press冲压punch press, dieing out press 冲床uncoiler & strainghtener 整平机feedero 送料机rack,j shelf, stack料架ec cylinder油缸robot 机械手taker 取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch 寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop定位块reset 复位smoothly顺利dent 压痕scratch刮伤deformation变形filings 铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock 库存receive 领取approval examine and verify审查processing, to process加工delivery, to deliver交货To return/delivery to. to senddregistration 登记lregistration card 登记卡ito control管束vto put forward and hand in提报safe stock安全库存racceptance = receive查收yto notice通知aconsume,pb consumption耗费apto fill in 填写clabrasion磨损reverseik angle = chamfer 倒角character die 字模toa collect, to gather采集toifailure, trouble故障statistics统计demand and supply需求career card简历卡to take apart a die卸掉模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓easily damaged parts 易损件standard parts 标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die模具figure file, chart file 图档 cuprogressive die, follow (-on)die 连t续模compoundt die复合模punchedi hole冲孔panel board镶块gtod bending折弯toi pull, to stretch拉伸Line stretching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边bto stake 铆合ldesigning, to design设计adesign modification设计变化ndie block 模块kfolded block折弯块sliding block滑块location pin 定位销lifting pin 顶料销die plate, front board模板padding block垫块stepping bar垫条eupper die base上模座lower die base下模座upper supporting blank上承板spare dies模具备品spring弹簧bolt 螺栓document folder活页夹file folder资料夹to put file in order整理资料first count初盘人first check初盘复棹人second count复盘人second check复盘复核人equipment设施waste materials废料casing = containerization 装箱quantity of physical inventorysecond count 复清点数目Quantity of customs count会计师盘 ,点数目the first page第一联filed by accounting department for reference 会计部存查end-user/using unit(department) 使用单位Summary of year-endphysical inventory bills年关清点截止票据汇总表bill name票据名称This sheet and physical inventorylist will be sent to accounting department together (Those ofNHK will be sent to financial department)本表请与清点清册一同送会计部－(NHK 厂区送财会部)Application status records ofyear-end physical inventory Listand physical inventory card年关库存货龄剖析表Blank and waste sheet NO.on-hand inventory现有库存空白与作废单号available material良品可使用plate 电镀obsolete material良品已呆板mold 成型to be inspected or reworked material for engineering mold待验或重工testing 工程试模资料total 共计not included in physical inventory cause description原由说明不列入清点part number/ P/N料号sample 样品type 形态incoming material to be inspected item/group/class类型进货待验quality 质量description 品名prepared by 制表steel/rolled steel 钢材notes 说明Material statistics sheet Year-end physical inventory物料统计明细表difference analysis sheetmeeting minutes 会议记录年关清点差别剖析表meeting type 会别physical inventory清点数目location地址difference quantity差别量chairman 主席cause analysis原由剖析present members 列席人员raw materials 原料subject主题materials 物料conclusion结论finished product成品decision items 决策事项semi-finished product半成品packing materials包材good product/accepted goods/ approved by / checked by /accepted parts/good parts良品prepared by批准 /审查 /包办defective product/non-good parts不PCE assembly production良品schedule sheet disposed goods办理品PCE 组装厂生产排配表warehouse/hub库房model 机锺on way location在途仓work order工令oversea location国外仓revision版次spare parts physical inventory list remark备注备品清点清单production control confirmation生产确认skid/pallet栈板checked by初审tox machine自铆机approved by批准wire EDM 线割department部门EDM 放电机Stock age analysis sheet coil stock 卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot 导正筒trim 剪外边pierce 剪内边drag form压锻差slug hole 废料孔 featuredie 公母模 expansiondwg 睁开图radius 半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block 定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch 压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block 衬套insert 入块club car高尔夫球车capability能力parameter参数factor 系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel 斜视规blanking穿落模dejecting顶固模demagnetization 去磁 ;消磁high-speed transmission 高速传达heat dissipation 热传 rack 上料degrease脱脂rinse 水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸办理Anodize阳性办理seal 封孔revision 版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products办理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate 坐标dismantle the die折模auxiliary function协助功能poly-line多义线heater band加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate 打浇口dryer 烘干机induction感觉induction light感觉光reram 连杆spedge finder巡边器concave凸convex凹short 射料不足nick 缺口speck 瑕疪shine 亮班splay银纹gas mark焦痕delamination起鳞cold slug冷块blush导色gouge 沟槽 ;凿槽satin texture段面咬花witness line证示线patent 专利grit 沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe 车mill 锉plane 刨grind 磨drill 铝boring镗blister气泡fillet 镶 ;嵌边through-hole form通孔形式roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angular offset 角度误差velocity 速度torque 扭矩spline=the multiple keys 花键quenching 淬火tempering回火annealing退火carbonization碳化alloy 合金organic solvent有机溶剂bracket小磁导liaison 联系单volatile挥发性resistance电阻ion 离子titrator 滴定仪beacon警告灯coolant冷却液crusher破裂机模具工程类plain die简略模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die 剪边模riveting die铆合模pierce 冲孔forming 成型 (抽凸 ,冲凸 ) draw hole抽孔bending折弯trim 切边emboss凸点dome 凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove 压线blanking下料stamp letter冲字 (料号 ) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg睁开图procedure dwg工程图die structure dwg模具构造图material 材质material thickness料片厚度factor 系数upward 向上downward 向下press specification冲床规格die height range合用模高die height闭模高度burr 毛边gap 空隙weight 重量total wt. 总重量punch wt. 上模重量五金部件类inner guiding post内导柱dowel pin固定销coil spring弹簧lifter pin顶料销pin 销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模 (凹模 )upper plate上模板lower plate下模板die pad 下垫板die holder下夹板die set 下模座bottom block下垫脚bottom plate下托板 (底板)stripping plate内外打 (脱料板 )outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板部件类punch 冲头insert 入块 (嵌入件 ) deburringpunch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch异形冲子bending block折刀roller 滚轴baffle plate 挡块located block定位块supporting block for location定位支承块air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 增强筋冲子ribbon punch压筋冲子guide plate定位板sliding block滑块active plate活动板lower sliding plate下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱two plate两极式（模具）runner system 浇道系统well type蓄料井stress crack应力电裂bushing block 衬套insulated runner 绝缘浇道方式orientation定向cover plate盖板hot runner热浇道sprue gate射料浇口，直浇口guide pad导料块runner plat浇道模块nozzle 射嘴塑件 & 模具有关英文valve gate阀门浇口sprue lock pin 料头钩销 (拉料杆 ) compre sion molding压缩成型band heater环带状的电热器slag well冷料井flash mold溢流式模具spindle 阀针side gate侧浇口spear head刨尖头edge gate侧缘浇口split mold切割式模具slag well冷料井tab gate搭接浇口cavity 型控母模cold slag冷料渣film gate薄膜浇口core 模心公模air vent排气道flash gate闸门浇口taper 锥拔h=0.02~0.05mm slit gate 空隙浇口leather cloak 仿皮革w=3.2mm fan gate扇形浇口shiver 饰纹L=3~5mm dish gate因盘形浇口flow mark流痕welding line熔合痕H=F=1/2t~1/5twelding mark 溶合痕eject pin顶出针T=2.5~3.5mmknock pin顶出销diaphragm gate 隔阂浇口self tapping screw自攻螺丝return pin回位销反顶针ring gate环形浇口striper plate 脱料板sleeve 套筒submarine gate 潜入式浇口piston 活塞stripper plate脱料板tunnel gate地道式浇口cylinder 汽缸套insert core搁置入子pin gate针点浇口chip 细碎物Φ 0.8~1.0mmhandle mold 手持式模具guide pin导销Runner less无浇道移转成型用模具(sprue less)无射料管方式e subzero深冷办理long nozzle延伸喷嘴方式射出成型用模具three plate三极式模具sprue 浇口 ;溶渣n质c量人员名称类aQCpFQC sIPQC uOQClIQCaTQCtPOCiQAoOQAnQE质量保证类mFAIoFAAlTVRdi quality control质量管理人员final quality control终点质量管理人员in process quality control制程中的质量管理人员output quality control最后出货质量管理人员incoming quality control进料质量管理人员total quality control全面质量管理passage quality control段检人员quality assurance质量保证人员output quality assurance出货质量保证人员quality engineering质量工程人员first article inspection新品首件检查first article assurance首件确认tool verification report模具确认报告3B3B模具正式投产前确认CP capability index能力指数CPK capability index of process模具制程能力参数SSQA standardized supplier quality合格供货商质量评估OOBA out of box audit开箱检查QFD quality function deployment质量机能睁开FMEA failure model effectiveness analysis无效模式剖析8D8 disciplines8 项答复内容FA final audit最后一次稽核CAR corrective action request更正行动要求corrective action report更正行动报告FQC 运作类AQL Acceptable Quality Level运作类允收质量水平S/S Sample size抽样查验样本大小ACC Accept允收REE Reject拒收CR Critical极严重的MAJ Major主要的MIN Minor稍微的AOQ Average Output Quality均匀出厂质量AOQL Average Output Quality Level均匀出厂质量Q/R/S Quality/Reliability/Service质量 /靠谱度服务MIL-STD Military-Standard军用标准S I-S IV Special I-Special IV特别抽样水同等级P/N Part Number料号L/N Lot Number特采AOD Accept On Deviation特采UAI Use As It首件检查报告FPIR First Piece Inspection Report百万分之一PPM Percent Per Million批号制程统计品管专类SPC Statistical Process Control统计制程管束SQC Statistical Quality Control统计质量管理R Range全距AR Average Range全距均匀值UCL Upper Central Limit管束上限LCL Lower Central Limit管束下限MAX Maximum最大值MIN Minimum最小值GRR Gauge Reproducibility & Repeatability量具之再制性及重测性判断量靠谱与否DIM Dimension尺寸DIA Diameter直径FREQ Frequency频次N Number样品数其余质量术语类QCC Quality Control Circle质量圈QIT Quality Improvement Team质量改良小组PDCA Plan Do Check Action计划履行检查总结ZD Zero Defect零弊端QI Quality Improvement质量改良QP Quality Policy目标目标TQM Total Quality Management全面质量管理MRB Material Reject Bill退货单LQL Limiting Quality Level最低质量水平RMA Return Material Audit退料认同QAN Quality Ameliorate Notice质量改良活动ADM Absolute Dimension Measurement全尺寸丈量QT Quality Target质量目标7QCTools7 Quality Control Tools品管七大手法通用之件类ECN Engineering Change Notes工程更改通知 (供货商 ) ECO Engineering Change Order工程变动要求 (客户 ) PCN Process Change Notice工序变动通知PMP Product Management Plan生产管束计划SIP Specification In Process制程查验规格SOP Standard Operation Procedure制做作业规范IS Inspection Specification成品查验规范BOM Bill Of Material物料清单PS Package Specification包装规范SPEC Specification规格DWG Drawing图面系统文件类QC Quality System质量系统ES Engineering Standardization工程标准CGOO China General PCE 龙华厂文件H Huston(美国 )休斯敦C Compaq(美国 )康伯企业C China中国大陆A Assembly组装(厂)S Stamping冲压(厂)P Painting烤漆(厂)I Intel英特尔企业T TAIWAN台湾IWS International Workman Standard工艺标准ISO International Standard Organization国际标准化组织GS General Specification一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制做作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control生产和物料控制PPC Production Plan Control生产计划控制MC Material Control物料控制ME Manufacture Engineering制造工程部PE Project Engineering产品工程部A/C Accountant Dept会计部P/A Personal & Administration人事行政部DC Document Center资猜中心QE Quality Engineering质量工程 (部 )QA Quality Assurance质量保证 (处 )QC Quality Control质量管理 (课 )PD Product Department生产部LAB Library实验室IE Industrial Engineering工业工程R&D Research & Design设计开发部P Painting烤漆(厂)A Assembly组装(厂)S Stamping冲压(厂)生产类PCS Pieces个(根,块等 )PRS Pairs双(平等 )CTN Carton卡通箱PAL Pallet/skid栈板PO Purchasing Order采买订单MO Manufacture Order生产单D/C Date Code生产日期码ID/C Identification Code(供货商 )辨别码SWR Special Work Request特别工作需求L/N Lot Number批号P/N Part Number料号其余OEM Original Equipment Manufacture原设施制造PCE Personal Computer Enclosure个人计算机外设PC Personal Computer个人计算机CPU Central Processing Unit中央办理器SECC SECC`电解片SGCC SGCC热浸镀锌资料NHK North of Hongkong中国大陆PRC People's Republic of China中国大陆the United States of America美国As Soon As Possible尽可能快的E-MAIL Electrical-Mail电子邮件N/A Not Applicable不合用QTY Quantity数目VS以及REV Revision版本JIT Just In Time零库存I/O Input/Output输入 /输出OK Ok好NG Not Good不可以 ,不合格C=0Critical=0极严重不同意ESD Electry-static Discharge静电排放5S希腊语整理 ,整改 ,打扫 ,洁净 , 修养ATIN Attention知会CC Carbon Copy副本复印有关人员APP Approve批准 ,认同 ,认可CHK Check确认AM Ante Meridian上午PM Post Meridian下午CD Compact Disk光盘CD-ROM Compact Disk Read-Only Memory只读光盘FDD Floppy Disk Drive软盘机HDD Hard Disk Drive碟碟机REF Reference仅供参照CONN Connector连结器CAV Cavity模穴CAD Computer Aid Design计算器协助设计ASS'Y Assembly装置 ,组装MAT'S Material资料IC Integrated Circuit集成电路T/P True Position真位度TYP Type种类WDR Weekly Delivery Requirement周出货需求C?T Cycle Time制程周期L/T Lead Time前置时间 (生产前准备时间 )S/T Standard Time标准时间P/M Product Market产品市场3C Computer,Commumcation,Consumer electronic's花费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time人力 ,物力 ,财务 ,技术 , 时间 (资源 ) SQA Strategy Quality Assurance策略质量保证DQA Design Quality Assurance设计质量保证MQA Manufacture Quality Assurance制造质量保证SSQA Sales and service Quality Assurance销售及服务质量保证LRR Lot Reject Rate批退率BS Brain storming脑力激荡EMI Electronic Magnet Inspect高磁测试FMI Frequency Modulated Inspect高频测试B/M Boar/Molding (flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply电源箱DT Desk Top卧式 (机箱 )MT Mini-Tower立式 (机箱 )DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system先进的基本输入 /输出系统CMOS Complementary Metal-Oxide-Semiconductor Transistor互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit集成电路ISA Industry Standard Architecture工业标准体系构造MCA Micro Channel Architecture微信道构造EISA Extended Industry Standard Architecture扩大的工业标准构造SIMM Single in-line memory module单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode发光二级管FMEA Failure Mode Effectiveness无效模式剖析W/H Wire Harness金属线绪束集组件F/C Flat Cable排线PCB Printed Circuit Board印刷电路板CAR Correction Action Report改良报告NG Not Good不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million百万分之一TPM Total Production Maintenance全面生产养护MRP Material Requirement Planning物料需计划OS Operation System操作系统TBA To Be Design待定 ,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry电子音乐工业RFI Read Frequency Input读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size。
英语专业工厂词汇
英语专业工厂词汇组装、冲压、喷漆等专业词汇Assembly line组装线 Layout布置图Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair 修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板rear plate后板 chassis 基座 bezel panel面板 power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序material check list物料检查表 work cell工作间 trolley台车 carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手hydraulic machine油压机 lathe车床planer |'plein|刨床miller铣床 grinder磨床 driller??床linear cutting线切割 electrical sparkle电火花 welder电焊机staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长department director部长deputy manager | =vice manager副理 section supervisor课长deputy section supervisor =vice section superisor副课长groupleader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布to load material上料 to unload material卸料to return material/stock to退料scraped |'skræpid|报废 scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤 dents压痕defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练proposal improvement提案改善 spare parts=buffer备件 forklift叉车trailer=long vehicle拖板车 compound die合模 die locker锁模器pressure plate=plate pinch压板 bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器defective product label不良标签identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板stopper阻挡器 flow board流水板hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套glove(s) with exposed fingers割手套thumb大拇指 forefinger食指midfinger中指 ring finger无名指 little finger小指 band-aid创可贴iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver 起子头 sweeper扫把 mop拖把vaccum cleaner吸尘器 rag 抹布garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条jack升降机production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架感谢您的阅读，祝您生活愉快。
工厂常用英语
制功课经常应用英语词汇总司理办公室General manager’s office模具部Tooling department项目部Project department品德部Quality department筹划部 Plan department制作部Manufacture departmentKeypad产品部Keypad departmentIMD 产品部 IMD department五金部 Metal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section 筹划科 Plan section仓务科 Warehouse section商务科 Business section品德筹划科 quality plan sectionIQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中间 measurement center项目筹划科 Project plan section项目XX科 Project section XX试模科 Mold test section成本科 Cost section装备科 Facility section倾销科 Purchase section分解办 General affairs office编程科 Programming section模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中间 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop装配车间Assembly workshop总司理General manager (GM)司理managerXX部分司理Manager of XX department原料库 Raw material warehouse半成品库 Semi-finished product warehouse 成品库 Finished product warehouse科长 section chief主任 chief部分主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary文员clerk操纵员operator助理assistant人员staff二.产品超声波焊接ultrasonic welding 塑胶件 Plastic parts塑材 Raw parts喷涂件 Painted parts装配件 Assembly parts零件 Component原料 Raw material油漆 Paint稀释剂 Thinner油墨 Ink物料编号part number三.模具注塑模具injection mold冲压模具Stamping tool模架mold base定模座板Fixed clamp plateA板A plateB板B plate支承板 support plate方铁 spacer plate回位销 Return pin导柱 Guide pin动模座板Moving clamp plate 顶针ejector pin单腔模具single cavity mold 多腔模具multi-cavity mold浇口gate合模力clamping force锁模力locking force开裂crack轮回时光cycle time老化aging螺杆screw镶件 Insert主流道 sprue分流道runner浇口gate直浇口 direct gate点浇口pin-point gate测浇口edge gate埋伏浇口submarine gate浇口套sprue bush流道板runner plate排气槽vent分型线（面）parting line定模Fixed mold动模movable mold型腔cavity凹模cavity plate,凸模core plate斜销angle pin滑块slide拉料杆sprue puller定位环locating ring脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mold熔合纹weld line三板式模具three plate mold脱模ejection脱模剂release agent打针才能shot capacity打针速度injection rate打针压力injection pressure保压时光holding time闭模时光closing time电加工装备Electron Discharge Machining数控加工中间CNC machine center全能铁床Universal milling machine平面磨床Surface grinding machine全能摇臂钻床Universal radial movable driller 立式钻床Vertical driller倒角chamfer键Key键槽keyway间距pitch快速成型模Rapid prototype tool （RPT）四.品管SPC statistic process control品德包管Quality Assurance(QA)品德掌握Quality control(QC)来料磨练IQC Incoming quality control 巡检IPQC In-process quality control校订calibration情况实验Environmental test光泽gloss拉伸强度tensile strength盐雾实验salt spray test翘曲warp比重specific gravity疲惫fatigue扯破强度tear strength缩痕sink mark经久性durability抽样sampling样品数目sample sizeAQL Acceptable Quality level批量lot size抽样筹划sampling plan抗张强度 Tensile Strength抗折强度 Flexural Strength硬度 Rigidity色差 Color Difference涂镀层厚度 Coating Thickness导电机能 Electric Conductivity粘度 viscosity附出力 adhesion耐磨 Abrasion resistance尺寸 Dimension(喷涂)外不雅问题 Cosmetic issue不及格品 Non-conforming product限度样板 Limit sample五.临盆注塑机injection machine冲床Punch machine嵌件注塑 Insert molding双色注塑 Double injection molding薄壁注塑 Thin wall molding膜内注塑 IMD molding ( In-mold decoration）移印 Tampo printing丝印 Silk screen printing热熔 Heat staking超声熔接 Ultrasonic welding (USW）尼龙nylon黄铜 brass青铜 bronze紫(纯)铜 copper料斗hopper麻点pit配料compounding涂层coating飞边flash缺料 Short mold烧焦 Burn mark缩水 Sink mark气泡 Bubbles决裂 Crack熔合线 Welding line流痕 Flow mark银条 Silver streak黑条 Black streak概况光泽不良Lusterless概况剥离Pelling翘曲变形Deformation脏圬 Stain mark油污 Oil mark蓝黑点 Blue-black mark顶白 Pin mark拉伤 Scratch限度样品 Limit sample最佳样品 Golden sample预热preheating再生料recycle material机械手 Robot机械人 Servo robot试临盆 Trial run; Pilot run (PR)量产 mass production切料头 Degate产能 Capacity才能 Capability参数 Parameter二次加工 Secondary process六．物控保质期shelf lifeABC分类法ABC Classification装配Assembly平均库存Average Inventory批号Batch Number批量临盆Mass Production提货单Bill of Lading物料清单Bill of Material倾销员Buyer检讨点Check Point有用日期Date Available修正日期Date Changed停止日期Date Closed截止日期Date Due临盆日期Date in Produced库存调剂日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required需求治理Demand Management需求Demand工程变动生效日期Engineering Change Effect Date 呆滞材料剖析Excess Material Analysis完整跟踪Full Pegging在成品库存In Process Inventory投入/产出掌握Input/ Output Control磨练标识Inspection ID库存周转率Inventory Carry Rate准时制临盆Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time负荷Loading仓位代码Location Code仓位状态Location Status批量标识Lot ID批量编号Lot Number批量Lot Size机械才能Machine Capacity机械加载Machine Loading制作周期时光Manufacturing Cycle Time制作资本筹划Manufacturing Resource Planning (MRP II)物料成本Material Cost物料发送和吸收Material Issues and Receipts物料需求筹划Material Requirements Planning现有库存量On-hand Balance订单输入Order Entry零件批次Part Lot零件编号Part Number (P/N)零件Part领料单Picking List领料/提货Picking产品掌握Product Control产品线Production Line倾销订单跟踪Purchase Order Tracking需求量Quantity Demand毛需求量Quantity Gross安然库存量Safety Stock在成品Work in Process零库存Zero Inventories七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan,产品德量先期筹划和掌握筹划PPAP Production Part Approval Process,临盆件同意程序FMEA Potential Failure Mode and Effects Analysis,潜在掉效模式及效果剖析MSA Measure System Analysis,测量体系剖析SPC Statistical Process Control,统计进程掌握审核 Audit才能 Capability才能指数 Capability Indices掌握筹划 Control Plans改正措施 Corrective Action文件 Documentation功课指点书 Standard operation procedure (SOP); Work instruction不及格品 Nonconformance不及格 Nonconformity每百万零件不及格数 Defective Parts Per Million, DPPM 预防措施 Preventive Action程序Procedures进程流程图 Process Flow Diagram, Process Flow Chart 质量手册Quality Manual质量筹划 Quality Plan质量筹划 Quality Planning质量记载Quality Records原始数据Raw Data反响筹划Reaction Plan返修Repair返工Rework现场Site分承包方Subcontractors产品product质量quality质量请求quality requirement顾客满足customer satisfaction质量治理体系quality management system质量方针quality policy质量目的quality objective质量治理quality management质量掌握quality control质量包管quality assurance组织organization顾客customer供方supplier进程process办事service设计与开辟design and development：特征characteristic可追溯性trace ability及格conformity缺点defect改正correction妥协concession放行release报废scrap规范specification磨练inspection实验test验证verification评审review测量measurement通俗原因Common Cause均值Mean极差Range稳固性Stability计量型数据Variables Data变差Variation反复性Repeatability再现性Reproducibility稳固性Stability分辩率Resolution进程更改Process change质量功效睁开QFD外不雅项目Appearance Item初始进程才能Preliminary Process Capability材料清单Bill of Material设计确认Design Validation设计验证Design Verification八．经常应用缩略词语OEM Original Equipment ManufacturerANOVA 方差剖析法 Analysis of VarianceDFMEA 设计掉效模式及效果剖析Design Failure Mode and Effects AnalysisDOE 实验设计 Design of ExperimentGR&R 量具的反复性和再现性Gage Repeatability and Reproducibility PFMEA 进程掉效模式及效果剖析Process Failure Mode and Effect AnalysisQSR 质量体系请求Quality System RequirementQFD 质量功效睁开 Quality Function DeploymentBOM 物料清单 Bill of MaterialCpk 稳固进程的才能指数 Capability for stable processLCL 下掌握限 Lower Control LimitUCL 上掌握限 Upper Control LimitLSL 工程规范下限 Lower Specification LimitX(—)--R图均值一极差图 Average-Range Chart防错（POKA-YOKE）Mistake ProofingETA 估计到达 Estimate to be arrivePO 定单 Purchase orderM/C 机械 machineRFQ 报价需求 Request for quotationMFI 熔融流淌指数 Melt flow indexFAI 全尺寸检测陈述 First article inspectionCOC 材质证实 Certificate of complianceALT 加快老化实验 Accelerated life testCRR 承认书 Component review reportOT 加班 Over timeCAP 改正筹划 Corrective action planR&D 研发 Research and DevelopmentASAP 尽快 As soon as possibleECN工程更改通知Engineering change noticeDCN 设计更改通知 Design change noticeOTD 准时交货 On time delivery九．通用词语确保 ensure构思 construct会签 con-sign功效 Function机构 organization外不雅 appearance实用 apply to功课流程 Operation flow附件 attachment商务人员 business personnel汇总 summarize指定相干人员 designated personnel新产品开辟解释会 new product development explanation meeting 拟定 Prepare委托 entrust认证 qualify电子档 Soft copy3D文件 3D database移转 Transfer履行 ConductXXX申请单 XXX Application form客户请求 Customer requirement启动 Kick off评估 Evaluation功课员 Operator同意, 承认 Approval合同评审 Contract review靠得住性 Reliability相干的 Relevant程序 Procedure制程 Process流程图 Flow chart产品 Product临盆 Production资材 Logistics义务 Responsibility跟进 Follow-up交付 Delivery汇总 Summarize外协加工 subcontract指定相干人员 designated personnel 编号 number附件 attachment产品名称 Description周期轮回时光 Cycle time模具号 Mold No,数目 quantity ( Qt’y )备注 remarkSAP号 SAP No.客户 Customer表单 Form初步的 Preliminary版本 Version根起源基础因 Root cause（喷漆）夹具 Fixture（装备）小夹具 Jig装备 Equipment举措措施 Facility送,提交（样品）Submit义务部分,义务人 Responsible by（大的）目的 Objective(小的,具体的)目的 Target格局 Format上岗证 Qualification card需求 Requirement现场 On site查检表 Checklist试产 pilot增值税 VAT---value-added tax品德专业英语大全零件材料类的专著名词CPU: central processing unit(中心处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（根本输入输出体系）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
质量部(Quality Depபைடு நூலகம்rtment )
1、 QC quality control 2、 FQC final quality control 3、 IPQC in process quality control 4、 OQC output quality control 5、 IQC incoming quality control 6、 TQC total quality control 7、 POC passage quality control 8、 QA quality assurance 9、 OQA output quality assurance 10 QE 10、QE quality engineering 11、FAI first article inspection 12、FAA first article assurance 13、TVR tool verification report 14、CP capability index 15、CPK capability index of process 16、SSQA standardized supplier quality 17、OOBA out of box audit 18、QFD quality function deployment 19、FA final audit 20、CAR corrective action request 品质管理人员 终点品质管制人员 制程中的品质管制人员 最终出货品质管制人员 进料品质管制人员 全面质量管理 段检人员 质量保证人员 出货质量保证人员 品质工程人员 新品首件检查 首件确认 模具确认报告 能力指数 模具制程能力参数 合格供应商品质评估 开箱检查 品质机能展开 最後一次稽核 改正行动要求
工厂常用英语
职位（Position ） 工程部 (Engineering Department ) 生产部(Productive Department ) 质量部(Quality Department ) 计划部(Planning Department ) 综合服务部(Synthesize Service Department )
1、 Board of Director 3、 Leader 5、 Factory Manager 7、 Manager 9、 Technician 11、Worker 13、Trainer
董事会 领导者 厂长 经理 技术员 工人 培训员
2、 Director 4、 General Manager 6、 Minister 8、 Engineer 10 、Cleanser 12、 Clerk 14、 Safe guardsman
36、 tube 套管 38、 Pilot-Run试作验证 40、 plastic 塑料,塑料 42、 primary(pri)初级 44、 solder wire锡丝 46、 Specification 生产规格 48、 straighten 弄直,使变直
soldering焊锡 step步序 tape 胶带
35、 equipment/instrument设备 37、 oven 烤箱 part number 品名 39、 pad 垫片 pin 脚 41、 Pre-soldering 预焊 43、 solder bar锡棒 solder iron 烙铁 45、 solvent 稀释剂 space winding疏绕 47、 stand-off 凸点 station 站别
Base 底座 18、 bifilar 双线并绕 Bobbin 绕线管 checked by审核 20、 Choke电感 clip耳夹
21、 Brush Epoxy On Core 铁芯刷胶 22、 Brush Epoxy On Loop 线圈刷胶 23、 close winding密绕 component 组件 24、 condition条件 core铁芯 25、 condition条件 copper铜箔 立式 26、 Curing烘烤 current 电流 27、 Cut wire 裁线 28、 defective product box不良品箱 29、 deficient manufacturing procedure制程不良 30、 description: 说明 31、 dip 浸入 Direction 方向 32、 Electronic Magnetic In EMI 抗电磁干扰 33、 Enameled copper wire 漆包线 34、 epoxy胶
29、 Visual management 目视管理 30、 bottleneck 瓶颈 31、 Layout 布置图 32、 continue Improvement持续改善: 33、 E: Elimination剔除 34、 C :Combination合并 35、 R: Re-arrangement重排 36、 S :Simplification简化 37、 PRA-Probabilistic Risk风险率评估 38、 Risk Priority Number (RPN) 风险关键指数 39、 What 完成了什么 where 何处做 40、 When 何时做 who 由谁做 41、 Why 为何这样做 how 何时做 42、 delay等待 43、 operation操作 44、 inspection检查 45、 transportation搬运 46、 storage储存 47、 Predetermined Motion Time Standard 简称PTS 预定动作时间标准法 48、 Methods-time-measurement 方法时间衡量 49、 Transport Empty 伸手 Grasp 握取 50、 Move 移物 Release Load 放手 51、 Disassemble 折卸 Use 应用 52、 Assemble 装配 Inspect 检查 53、 Search 寻找 Select 选择 54、 Play 计划 Pre-Position预定位 55、 Position 定位 Hold 持住 56、 Rest 休息 Avoidable Delay 故延 57、 PRA-Probabilistic Risk风险率评估 58、 Risk Priority Number 风险关键指数 59、 delay等待 operation操作 61、 storage储存 60、 inspection检查 transportation搬运 62、 Unavoidable Delay 迟延
22、AQL Acceptable Quality Level 运作类允收品质水准 23、 S/S Sample size 抽样检验样本大小 24、 ACC Accept 允收 25、 REE Reject 拒收 26、 CR Critical 极严重的 27、 MAJ Major 主要的 28、 MIN Minor 轻微的 29、 AOQ Average Output Quality 平均出厂品质 30、 AOQL Average Output Quality Level 平均出厂品质 31、 Q/R/S Quality/Reliability/Service 品质/可靠度服务 32、 MIL-STD Military-Standard 军用标准 33、 S I-S IV Special I-Special IV 特殊抽样水准等级 34、 P/N Part Number 料号 35、 L/N Lot Number 特采 36、 AOD Accept On Deviation 特采 37、 UAI Use As It 首件检查报告 35、 FPIR First Piece Inspection Report 百万分之一 38、 PPM Percent Per Million 批号 39、 SPC Statistical Process Control 统计制程管制 40、 SQC Statistical Quality Control 统计品质管制 41、 AR Averary Range 全距平均值 42、 UCL Upper Central Limit 管制上限 43、 LCL Lower Central Limit 管制下限 44、 MAX Maximum 最大值 45、 MIN Minimum 最小值
生产部(Productive Department )
1、Classification整理(sorting, organization)-seiri 2、 Regulation整顿(arrangement, tidiness)-seiton 3、 Cleanliness清扫(sweeping, purity)-seiso 4、 Conservation清洁(cleaning, cleanliness)-seiktsu 5、 Culture教养(discipline)-shitsuke 6、 Save 节约 Safety安全 7、 physical distribution物流 8 、 Materials handling物料搬运 9、 critical path method关键路线法 10、 optimistic time最乐观时间 11、 Most likely time最可能时间 12、 pessimistic time最悲观时间 13、 Mean time between failure 平均故障期 (MTBF) 14、 Mean time to repair 平均维修期(MTTR) 15、 Break PIN 折脚 16、 approved by: 核准 17、 assembly组合 19、 bottom 底部
董事/总监 总经理 部长 工程师 清洁员 文员 保安
工程部 (Engineering Department )
1、Industrial Engineering 工业工程 2、 Production Engineering 产品工程 3、 Test Engineering 测试工程 4、 Brain Storming 脑力激荡 5、 OEM:委托代工 (Original Equipment Manufacture) 6、 Temperature(temp)温度 7、 Fool-Proof 防止错误法 (防错法) 8、 work instruction /Standard Operating Procedure 作业指导书 9、 Facilities Design and Planning设施规划与设计 10、 Material Flow System Analysis物流系统分析 11、Cost Control成本控制 12、 Production Planning and Control生产计划与控制 13、 Humidity湿度 14、Human Engineering人机工程 15、 Value Engineering价值工程 16、 Work Assessment工作评价与考核 17、 leaning curve学习曲线 18、 Time measurement 时间测量 19、 Machine Interference机器干扰 20、 Shop floor observation 现场观测 21、 Single Minute Exchange of Dies (SMED) 六十秒即时换模 22、 Methods of time measurement标准时间测量(MTM) 23、 Waste浪费 24、 Line Balancing 线平衡 25、 Value有价值 No Value无价值 26、 Incidental work(necessary)必要 27、 Takt Time生产节拍 28、 Just In Time实时管理 (JIT)