冰柜使用说明书
冰柜使用说明书
Prepared on 24 November 2020
冰柜使用说明书
1、冰箱在搬运、放置过程中倾斜角不要超过45度。长途运输的冷
柜应放置2小时后方可通电使用，以防止系统压力过高而损坏。第一次
使用应当先让空柜运行1小时，当箱内温度下降后再放物品。
2、冰箱应选择远离热源、避免阳光直射、通风较好、较干燥的地方
放
（1）应安放在远离热源，不受阳光直射的地方，因工作时需要与外界
进行热交换，既通过冷凝器向外界散热，外界环境温度越高，散热越
慢，会使冰箱工作时间越长，增大耗电量，制冷效果差。
（2）应安放在湿度小的地方，由于电冰箱、冰柜外壳，冷凝器和压缩
机等均是金属材料，如果空气湿度太大，会使这些部件生锈，缩短电冰
箱的使用寿命。同时潮湿过热环境，会造成电冰箱表面凝露，影响电器
性能。
（3）应安放在通风良好的地方，如果电冰箱、冰柜周围堆满杂物，或
者靠墙太近，不利于散热会影响制冷效果。电冰箱背面和两侧面应留有
至少10CM的空间，以利散热。
（4）应安放在平坦坚实的地面上，并使压缩机保持水平。这不仅出于
安全的需要，而且可使压缩机平稳工作，减少震动和噪音。
（5）请勿损坏电源线绝缘层，不得重压电线，不得自行随意更改或加
长电源线。
（6）检查无误后，电冰箱、冰柜静置半小时，接通电源，仔细听压缩
机在启动和运行时的声音是否正常，是否有管路互相碰击的声音，如果
噪音过大，检查产品是否摆放平稳，各个管路是否接触，并做相应的调
整。若有较大的异常声音，应立即切断电源，与专业的修理人员联系。
新飞卧式冰柜220说明书
新飞卧式冰柜220说明书
1、系统上电时，按键指示LED，液晶屏全亮2秒，然后进入正
常显示。
2、长按Power键3秒，冰箱开机/待机（关机）。
3、开机状态，液晶屏正常显示，待机状态，液晶屏不工作。
4、按“+”或“-”键，进行预设温度，预设值以2HZ频率。
闪烁，长按“+”或“-”键，预设温度以4℃每秒速度线。
性调整（线性调整过程中数字不闪烁），同时按“+”和“-”键2秒，切换制冷，加热模式，蓝色显示表示制冷，橙色显示表示加热。
5、3S内，没有检测到任何按键动作后，预设值停止闪烁，退出预设，并保存当前预设值，液晶屏显示箱内实际温度。
6、工作状态下，按“SET”，进行MAX/ECO模式切换，压缩机转速，MAX：3800r/min，ECO：2500r/min。
7、60S按键自动上锁，显示屏显示箱内实际温度；上锁状态，
按下任意按键，液晶屏顺时针显示“”，然后显示。
箱内实际温度；在锁定状态下，长按“SET”3S，按键解锁，解锁时，液晶屏逆时针
显示“”。
8、在加热模式下，切换到制冷模式：如果箱中实际温度≥40℃，冰箱则。
处于保护状态，不制冷，LCD显示40，直到箱中实际温度
<40℃，冰箱。
则自动启动制冷。
如果箱中实际温度≥40℃，使用者
要求马上启动制冷，则可以先关掉冰箱电源再上电强行启动制冷。
美菱冰柜 BC BD-201DTECX 使用说明书
全国统一服务热线: 4008 111 666 (连拨,请勿加区号)
4006 111 666
图形仅为示意以实物为准
型号 气候类型 防触电保护类型 冷冻星级 总容积(L) 冷冻室容积(L) 额定电压(V~) 额定频率(Hz) 额定电流(A) 额定输入功率(W)
BC/BD-201DTECX SN/N/ST/T Ⅰ类
201 201 220 50 1.0 120
标准耗电量
(冷藏/冷冻)
(kW·h/24h) (kW·h/a)
能源效率等级 重量(kg)
制冷剂/充注量 冷冻能力(kg/12h) 冷却能力(kg/12h) 发泡层材料 噪声(声功率级)(dB(A))
外形尺寸(宽x深x高mm)
BC/BD-201DTECX
1
11
2024年7月版
0. 20.0
环戊烷 38
823×556×860
3、 当 环 温 ≤1 0℃ 时 ， 空 箱 最 低 温 度 可 达- 4 0℃,实 际 使 用 时 根 据 存 储 物 品 及 使 用 环 境 差 异, 箱内最低温度可能会有偏差。 （备注：按GB/T 8059-2016标准之7.8.3条所述间室空气温度测量方法进行测温点布置）
冰柜使用说明书-Jamajka W OPEN
Fig.1 Layout of unit “Jamaica W OPEN” 2Fig.2 Mounting the hook on the frame 3Fig.3 Adjusting the height of hooks4Fig.4 Assembly/disassembly of glass elements 4Fig.5 Control panel4Fig.6 Assembly/disassembly of suction 6Fig.7 Cleaning the condenser 6Fig.8 Replacing the fluorescent lamp 7Fig.9 Nameplate8Fig.10 “Igloo” thermostat panel 9Fig.11 “Carel” thermostat panel101. UNLOADINGThe unit should be transported in an upright position, properly secured and packed. The manufacturer sends the unit on a special wooden pallet, protected by cardboard angles and foil.2. PROPERTIES OF THE DEVICE2.1. Purpose“Jamaica W Open” was made without the front glass, which allows self-service sales. The cabinet is a universal cooling unit intended for exhibition and short-term storage of confectionery: cakes, pies, cookies, desserts, etc. at +8°C/+15°C at ambient temperature of +15°C/+25°C and relative air humidity of max. 60%.2.2. Description of the device“Jamaica W Open” is also fitted with an internal chiller controlled by an electronic thermostat, optionally working with the temperature recording module, which allows for recording and signaling whenever the temperature in the unit is too high or too low. Cooling is done by forced air circulation. The cabinet is equipped with automatic condensate evaporation and automatic defrosting. It is suitable for connecting in rows and can be supplied with an external chiller unit (“-mod C”). The display section of the cabinet consists of glass or metal shelves suspended on a frame. The shelves have the ability to change their height and angle. “IGLOO” devices are made using modern technology and have the certificates required by law.This sign signifies information of particular meaning for user security and for proper device exploitation.ContentsList of FiguresList of tablesTable 1 Technical data2User manual JAMAJKA W OPEN1.UNLOADING 12.PRODUCT FEATURES 12.1.Purpose 12.2.Device description 12.3.Technical data23.PREPARING THE UNIT FOR OPERATION 33.1.Requirements for the installation site 33.2.Connection and start-up 34.OPERATION 54.1.Temperature control 55.MAINTENANCE 55.1.Cleaning and maintenance 56.SERVICE 76.1.Identification and repair of faults 76.2.Maintenance 87.THERMOSTAT OPERATION 97.1.IGLOO Thermostat 97.2.CAREL Thermostat101 – Internal lighting2 – Internal back (perforated – DO NOT BLOCK THE VENTSto ensure chilled air circulation!)3 – Shelf price strip4 – Front glass grip5 – Low front glass6 – Airflow channel7 – Wooden housing8 – Chiller unit9 – Feet for leveling the unit10 – T op shelf (roof) – wooden or stainless steel11 – Rear of the unit (outer back)12 – Display shelf (glass or stainless steel)13 – Internal frame14 – Internal countertop15 – Control panel (thermostat, switches)16 – Nameplate17 – Windchest (After removing, access to the condenser fins isavailable. DO NOT OBSTRUCT THE VENTS2.3. Technical dataTable 1 Technical dataType of unit Rated voltage[V/Hz]Rated current[A]Rated lightingpower [W]Powerconsumption[kWh/24h]Shelf load[kg/m]Cooling po-wer demand[W/mb]Unit weight[kg]1.3W Open*230/50 4.714416.210-190 1.3W Open-mod/A *230/50 4.714416.210-180 1.3W Open-mod/C *230/50-144-10700170 0.9W Open *230/5037210.110-140 0.9W Open-mod/A *230/5037210.110-130 0.9W Open-mod/C *230/50-72-10700120 0.6W Open*230/502.2607.710-90 0.6W Open-mod/A *230/50 2.2607.710-80 0.6W Open-mod/C *230/50-60-1070070* Jamaica W Open” also has a wooden (RETRO/TREND) or stainless steel housing.3. PREPARING THE UNIT FOR OPERATION3.1. Requirements for the installation site• Check whether the cross-section of power cables is suitable for the current consumption of the installed equipment • It is forbidden to connect the device via extension cables or distributors•The unit must be connected to a separate, properly prepared electrical circuit with a socket with protective pin (as per PBUE)The unit may only be started after confirming the effectiveness of shock protection with the results ofmeasurements carried out in accordance with applicable regulations!3.2. Connection and start-up • Unpack the unit and remove the wooden pallet • Place the unit on a level and sufficiently solid surface, and then level it with the feet Fig.1/9 (p.3)• Remove protective film from the cabinet components •First cleaning of the unit should be done after unpacking the unit and prior to start-up. The device shouldbe cleaned with water at a temperature not exceeding 40°C with added natural cleaning agents. Cleaning and washing of the device must not be done using agents containing chlorine and different varieties of sodium, as they damage the protective layer and the unit’s components! Any residual adhesive or silicon on metal components may only be removed with petroleum ether (does not apply to plastics compo-nents!). Do not use other organic solvents.Do not use water jets while washing the unit. The unit should be cleaned with a damp cloth.• Place the plug of the connection cable directly into the socket (it is forbidden to connect the device via extension cables or distributors!)• Switch on the main switch Fig.5/1 (p.7), which will turn on the thermostat, and then the generator unit • In the thermostat panel Fig.5/3(p.7) set temperature a (detailed operation at p.14 or 15)• Press the lighting switch Fig.5/2 (p.7)Once the unit has been installed at its destination, leave it at rest for at least 2 hours before switching on (for equipment with internal generator unit), so that the oil level settles to prevent problems with starting the chiller!WARNING: Protect the cooling circuit against damage!• If the unit goes to the user partially disassembled for safety in transport, proceed as follows:1. Install the hooks with the lamp in the frame 2. Fig.2/3 (p.5)3.Place glass shelves on the frame and the internal countertop Fig.4/5,6 p.6) . Place glass components on silicon parts (bumpons) Fig.4/8 (p.6).3– Hook (fitted for three-step adjustment of the suspension angle)Fig.3 Adjusting the height of hooks 1 – Hook2 – The conduit tube shielding the lamp cord3 – PVC profile masking the frame’s vertical barT o change the height of the hook, slightly tilt the PVC profile and drag the conduit tube to the appropriate position. Then pull the hook fromthe frame and place it in the appropriate position and angle.Fig.4 Assembly/disassembly of glass elements 1 – Glass side2 – Front glass grip3 – Low front glass4 – T op aluminum profile (tilting guide) of the glass5 – Frame display shelf6 – Countertop display shelf7 – Bumpon – silicone element protecting glass componentsfrom moving and providing better grip (Do not damage during operation and maintenance!)8 – Frame hook11567822213344Fig.6 Control panel1 – Main switch (turns on/off the aggregate of thedevice)2 – Lighting switch3 – Thermostat (temperature regulator) panel (servi-ce details – Chapter No. 7, p. 21 and 22)4. OPERATIONThe cooling temperature and the work cycle of the unit may fluctuate. They depend on a number of factors, e.g. the amount and temperature of the products inside, and the ambient temperature.Place the unit in a dry, well-ventilated place without direct sunlight, ensuring good air exchange (distance between the wall and the device min. 10 cm), away from heat sources and devices forcing the airflow (portable and ceiling fans, blow heaters). The unit is functioning properly in an environment where the temperature is in the appropriate climate class, as indicated on the nameplate. Operation of the device may deteriorate if the temperature was above or below the indicated range for a long period.NOTES AND TIPS• Properly level the unit to prevent noisy operation and ensure proper (condensate) drainage during de-frosting• After transporting the unit, wait about 2 hours before restarting it• When first filling the cooling space, do so after it has cooled down to operating temperature.This principle should also be observed after a long downtime• Do not block any vents, as could hinder the circulation of cooled air. Y ou should also provide proper airflow around the unit (in any case, do not cover the vents)t• Ensure a uniform load on the shelves without exceeding their maximum load• Keeping the condenser clean. Impurities may cause overheating of the compressor and ultimately lead to failure, which is not covered by the warranty.• Do not use electrical appliances inside the chamber for storing food products4.1. Temperature controlFor operation of thermostats (temperature controllers) “Igloo” and “Carel”, see section 7 (p.14 and 15).The main task of the thermostat is to control the refrigerating unit, so as to reach the preset temperature within the unit and keep it within certain ranges. All temperature control settings necessary for normal functioning of the unit are introduced by the manufacturer. Before using the device, the user should check and set the desired temperature on the panel inside the device.Digital display – displays the current temperature inside the deviceAny interference in the factory settings of the thermostat voids the warranty!5. MAINTENANCE5.1. Cleaning and maintenanceAll maintenance services need to be performed after disconnecting the device from power supply!Protect the electrical installation against damage or floodingDo not use water jets while washing the unit. The unit should be cleaned with a damp cloth.Do not use any sharp objects to remove filth!Devices equipped with wheels cannot be used on uneven surfaces!Fig.6 Assembly/disassembly of suction1 – Internal countertop2 – Suction (DO NOT BLOCK the vents)Do not use mechanical means in order to fasten the defrosting process!Once a month it is recommended to stop the operation of the deviceto clean the interior, provide natural defrosting of the evaporator andto clean the condenser.The unit’s evaporator should be kept clean. Impurities impede heattransfer, resulting e.g. in increased electricity consumption and couldcause damage to the compressor unit.T o clean the condenser, unscrew the fixing screws and remove thewindscreen. Clean the condenser fins with a soft brush. For strongsoiling (clogging the fins) of the condenser, it is advisable to use avacuum or compressed nitrogen to suck out/blow out the soil frombetween the fins.Fig.10 Condenser cleaningThe manufacturer is not liable for damage to the condensing unit resulting from non-observance ofthe condenser’s cleanliness!Parts of the unit may corrode if used or maintained incorrectly. Follow the rules:• Do not let surfaces of the unit to come into contact with agents containing chlorine and sodium varieties that damage the protective layer and the unit’s components (including various gradesof stainless steel)Fig.8 Replacing the fluorescent lamp 1 – Lamp grip 2 – Lamp3 – Light housing4 – Fluorescent igniterDuring maintenance work, be careful not to damage the nameplate Fig.9 (p.13), which contains important information for maintenance workers and waste disposal companies.6. SERVICE6.1. Fault identification and repairIn case of any difficulties during actuation of the device or during its exploitation, please return to these chapters in this manual, which explain the performed operation. This aims to ensure that the device is properly operated. If you still experience difficulties, the following hints will help you solve the problem:The device is not working... – Make sure that:• The device is connected to the supply network• Voltage and frequency in the network are compliant with those recommended by the producer, 230V/50Hz • The main switch is turned on• Thermostat is turned on (This concerns the Igloo thermostat – If only two spots are visible on the display – turn onthe thermostat)The device is operating, but the lighting is off...– Make sure that:• Lighting switch is turned on• Fluorescent lamp or starting switch of the device is not burntThe device does not reach the proper temperature, the lighting is on...– Make sure that:• The main switch is on• T emperature setting on the thermostat is properly set • Thermostat works properly• The condenser is clean, if necessary – clean the condenser • Ambient temperature does not exceed 25ºC• Enough time has passed for products to be cooled • Ventilation holes of the device are not blocked(This concerns the “IGLOO” thermostat) thermostat displays C0 or C1 or C2 instead of displaying temperature:This situation shall occur, when one of temperature regulation sensors has been destroyed. The following messages may be displayed in such case:• C0 – temperature sensors inside the chamber are damaged – call authorized service • C1 – failure of evaporator sensor - call authorized service•C2 – failure of condenser alarm sensors (or failure of second evaporator sensor) – call authorized service(This concerns the “CAREL” thermostat) Thermostat displays E0 or E1 or L0 or HI or EE or Ed or DF insteadof temperature:• E0 – failure of temperature sensor inside the chamber – call authorized service• E1 – failure of evaporator sensor – call authorized service• L0 – low temperature alarm (lower than temperature range set within the device – call authorized service• HI – high temperature alarm – call authorized service• EE – internal defect of the regulator – call authorized service• Ed – max. defrosting time exceeded – call authorized service• DF – defrosting in progress (this is not an alarm signal) – call authorized service(This concerns the “IGLOO” thermostat) The device is working, sound signalling is activated...– Make sure that:• The condenser is clean, if necessary – clean the condenser• Condenser ventilator is working properly• Ambient temperature does not exceed 25ºCThe device is working too loud...– Make sure that:• The device is standing stably• Furniture adjoining the device do not vibrate when the cooling aggregate compressor is workingSounds made by equipment at work are normal. The equipment includes fans, motors and compres-sors, which turn on and off automatically. Every compressor produces a noise while at work. Thesesounds are generated by the motor unit and by the refrigerant flowing in the circuit. This pheno-menon is a technical characteristic of refrigeration units and does not mean malfunction.In the case of exceeding the ambient conditions as per third-class climate (relative humidity above 60%),the phenomenon of water transfer from the system with automatic condensate evaporation (evaporator)may be observed. This case does not mean malfunction and does not require a service call.Deposition of condensation on the unit’s windows at high relative humidity above 60% is a natural pheno-menon and does not require a service call!6.2. ServiceIGLOOservicetelephonenumber:+48(14)6621956or+48605606071e-mail:***************If after checking points described in chapter 6.1 “Fault identification and repair” the device still does not work properly, please contact T echnical Service of the Igloo company, stating the data from the data plate Fig.12 (p. 20):• Serial number (NS)• Production date• Type (name of the device)and• Date when the device was purchased• Description of the problem• Y our exact address and telephone number(with the code number)The above figure shows a demonstrative data plate andthe data stated on the plate are exemplary data, whichare not related with “Jamajka W OPEN” devices!Fig.12 Data plate7. THERMOSTAT SERVICE7.1. …IGLOO” thermostatFig.13 …Igloo” thermostat control panelVerification of adjusted temperature (inside the device) – By pressing “▲” or “▼” switch once we can verify the adjusted temperature. The adjusted temperature shall be shown on the display with a visible red blinking spot (diode). The preview shall finish automatically after about 3 seconds.Lowering (or increasing) the temperature – press “▼” (or “▲”) switch and the adjusted temperature shall be visible on control panel. By pressing the “▼” switch we decrease the temperature to the desired value. The preview shall finish automatically after about 3 seconds.Manual defrosting – switch No. 2 enables to initiate the defrosting cycle at any moment when the device is working (re-gardless of the automatic defrosting function); the switch shall not operate when the temperature is higher than the final defrosting temperature.The user should switch on/ switch off the aggregate only by means of the main switch of the device, and not by means of the direct switch on thermostat control panel. Switching on the main switch shall automa-tically initiate the thermostat!* Read more on www.igloo.pl1 – Cooling on/off switch2 – Manual defrosting switch3 – Aggregate and defrosting operating control diode4 – T emperature monitoring switch on defrosting sensor5 – T emperature regulation switch (increase)6 – Temperature regulation switch (decrease)7.2. …CAREL” thermostatFig.14 …Carel” thermostat control panelWHAT DO DIODES ON CONTROL PANEL SIGNIFYDiode 1 is on - Compressor: the symbol is visible when the compressor is working. It is blinking when compressor actuation is delayed by security procedure. It blinks in the following cycle: two blinks – pause, when the constant working mode is activated.Diode 2 is on - Ventilator: the symbol is visible when evaporator ventilators are turned on. It blinks when the actuation of the ventilators is delayed by external disengagement or when another procedure is in progress.Diode 3 is on - Defrosting: the symbol is visible when the defrosting function is activated. It blinks when the actuation is delayed by external disengagement or when another procedure is in progress.Diode 4 is on - Alarm: the symbol is visible when the alarm is activated.5 – current temperature inside the device is displayed (decimal places displayed after the comma)SETTING THE DESIRED TEMPERATURE- press for 1 second leading value shall be displayed on the screen;- increase or decrease the leading value by means of and , switches, until the desired value shall be obtained; - press once again in order to confirm the new value of the setting point;MANUAL INPUT OF THE DEFROSTING CYCLEDefrosting shall be realised in an automatic mode. It is possible to force defrosting at any moment by pressing and holding the switch for minimum 5 seconds. Diode No. 1 shall blink during manual defrosting.* Read more on www.alfaco.plNOTE: IN CASE OF NOT OBSERVING THE PRINCIPLES ON CONNECTING AND USING THE DEVICE INCLU-DED IN THIS MANUAL, THE PRODUCER SHALL RESERVE THE RIGHT TO RECEDE FROM OBLIGATIONS OF THE GUARANTORInformation included in this document may be altered by “IGLOO” without noticing the user.Copying the present manual without the consent of the producer is forbidden.Images and drawings are of demonstrative character and may differ from the purchased device.。
广东星星不锈钢冰柜说明书
广东星星不锈钢冰柜说明书1、初次上电冰箱初次连接电源后，显示屏点亮，冰箱默认为开启智能功能，变温室默认为0℃；2、显示屏锁定/解锁自动锁定：冷藏门关闭且30秒内没有按键操作时，显示屏自动熄灭并锁定；手动锁定：显示屏解锁状态下，按下童锁功能按键持续3秒，蜂鸣器响一声，锁定图标点亮，显示屏锁定，无按键操作30秒后锁定图标熄灭；解锁：显示屏熄灭状态下，打开冷藏门或触摸显示屏任一按键，锁定图标点亮，此时按下童锁按键并持续3秒，蜂鸣器响一声，锁定图标熄灭，显示屏解锁并点亮；3、冷藏室温度调节（2到10℃）和冷藏室开关功能显示屏解锁状态下，按一下冷藏温度调节按键，蜂鸣器响一声，进入冷藏室温度设置状态，每按一下冷藏温度调节按键，蜂鸣器响一声，冷藏室设定档位减1，冷藏室档位在10到9到2到OF之间循环。
当冷藏室设置在OF档位时，可以实现关闭冷藏室，设置其他温度档位时，冷藏室开启并制冷；4、变温室温度调节（7到-18℃）和变温室开关功能显示屏解锁状态下，按一下变温温度调节按键，蜂鸣器响一声，进入变温室温度设置状态，每按一下变温温度调节按键，蜂鸣器响一声，变温室设定档位减1，冷藏室档位在7到6到-18到OF之间循环。
当变温室设置在OF档位时，可以实现关闭变温室，设置其他温度档位时，变温室开启并制冷；5、冷冻室温度调节（-16到-24℃）和冷冻室开关功能显示屏解锁状态下，按一下冷冻温度调节按键，蜂鸣器响一声，进入冷冻室温度设置状态，每按一下冷冻温度调节按键，蜂鸣器响一声，冷冻室设定档位减1，冷冻室档位在-16到-24之间循环。
6、智能功能在环境温度波动较大时，智能功能能确保冰箱自行正常工作。
冰箱根据环境温度的变化，自动调节温度设定。
显示屏解锁状态下，按下智能功能按键，蜂鸣器响一声，智能功能指示图标点亮，冰箱智能功能开启；智能功能图标点亮状态下，按下智能功能按键，蜂鸣器响一声，智能功能图标熄灭，即智能功能关闭。
7、速冻功能速冻功能是为了保存冷冻食品的营养价值而设计的，它将食品在最短的时间内冻透。
ksv-410d说明书冰柜
ksv-410d说明书冰柜
1、冰柜在搬运、放置过程中倾斜角不要超过45度。
长途运输的冷柜应放置2小时后方可通电使用，以防止系统压力过高而损坏。
第一次使用应当先让空柜运行1小时，当箱内温度下降后再放物品。
2、冰柜应选择远离热源、避免阳光直射、通风较好、较干燥的地方(1)应安放在远离热源，不受阳光直射的地方，因工作时需要与外界进行热交换，既通过冷凝器向外界散热，外界环境温度越高，散热越慢，会使冰柜工作时间越长，增大耗电量，制冷效果差。
(2)应安放在湿度小的地方，由于电冰柜、冰柜外壳，冷凝器和压缩机等均是金属材料，如果空气湿度太大，会使这些部件生锈，缩短电冰柜的使用寿命。
同时潮湿过热环境，会造成电冰柜表面凝露，影响电器性能。
(3)应安放在通风良好的地方，如果电冰柜、冰柜周围堆满杂物，或者靠墙太近，不利于散热会影响制冷效果。
电冰柜背面和两侧面应留有至少10CM的空间，以利散热。
(4)应安放在平坦坚实的地面上，并使压缩机保持水平。
这不仅出于安全的需要，而且可使压缩机平稳工作，减少震动和噪音。
(5)请勿损坏电源线绝缘层，不得重压电线，不得行随意更改或加长电源线。
冷藏不锈钢水箱可以放入清洁的水来冷却瓶装饮料放入前须开面两个小时待冷藏箱的温度达到所需的要求时再将水放入。
一般放
入的水只须冷藏箱容积的1/31/2为宜。
放入水后一般需516小时的运行时间箱中的水方可冷冻到0—7℃这时就可将瓶装饮料慢慢放放水中。
如开门次数较少或周转饮料次数较少箱壁结霜或冰属正常现象。
请即时翻动或移出靠近箱壁的瓶装饮防止爆。
冰柜keld温控器说明书
冰柜keld温控器说明书
1、开关机：把拨动开关拨动到ON位置，温控器开机；把开关拨动到OFF位置，温控器关机。
2、工作模式设定：把拨动开关拨动到COOL位置，温控器设定为制冷
模式；把拨动开关拨动到HEAF位置，温控器设定为制热模式。
3、温度设定：机械式温控器，采用旋钮式设定温度，把红点对着面
板标明的温度数据即可。
4、风速设定：把开关拨动到LOW位置；温控器设定为低档风速；把
开关拨动到WED位置，温控器设定为中档风速；把开关拨动到High位置，温控器设定为高档风速。
液晶温控器操作方法
1、为开关机键，按键选择系统的开机或关机状态。
2、M：模式键，按键选择系统的控制模式，是制冷还是制热，制冷就
是降低环境温度，反之既是制热了。
3、风速键，按键选择输出风的大小，风速可以分为三类：低档、中
档和高档，不同的叶片，从多到少依次代表高、中、低。
4、设定温度。
可以设定温度的高低，如果您需要制热，此时您所设
定温度应该高于室内温度，模式为制热，反之低于室内温度，模式为制冷。
海尔 BC BD-200GHDT 200升冷藏冷冻转换柜 使用说明书
感谢您选择和使用我们的产品。
我们承诺：您的产品需要安装或维修等服务时，我们将提供：“1+5″的成套服务： 1：一次就好服务。
5：五项增值服务：（1）安全测电服务：为您提供安全测电并提醒讲解到位服务；（2）讲解指导服务：向您讲解产品使用、保养常识，指导用户正确使用服务；（3）一站通检服务：服务好本产品，对家中其他本企业产品进行通检服务；（4）全程无忧服务：为您提供设计、送货、安装、清洗、延保、以旧换新等服务；（5）现场清理服务：服务完成后将服务现场清理干净。
为体现真诚、贴心，我们友情提醒：产品的安装服务，因用户的安装环境、个性需求不同，安装过程中如需辅加材料或有特殊服务项目需要支付材料等费用，您可通过“海尔智家”APP-“家电服务”-“收费标准”进行查看，并给予监督。
如未按标准收费或服务规范执行不到位，可拨打服务监督电话400 699 9999，或通过“海尔智家”APP-“家电服务”、“在线客服”进行监督、评价。
如果您的产品有服务需求，欢迎体验海尔智家自助服务专区（预约服务、一键安装、一键维修）：手机搜索安装“海尔智家”APP，您可通过“家电服务”版块选择安装、维修等服务。
如您需要选购更多产品，可在“海尔智家”APP-“商城”进行选购。
（更便捷、更快速、更省钱）期待您的参与！请扫描机身二维码，了解《绿色产品标识》详情尊敬的用户：地址：青岛经济技术开发区海尔工业园青岛海尔特种电冰柜有限公司版次：2023年第1版专用号：0070518107厂家代码：VC00000检验印章： QC 02产品合格证产品名称：见铭牌 产品型号：见铭牌 出厂编号：见条码检验日期：见条码检验结论： 检验合格准予出厂0070518107对应的条形码BC/BD-100GHT/GHZT/GHMT/GHZA型号:BC/BD-142GHT/GHZT/GHZABC/BD-200GHT/GHZT/GHMT/GHZABC/BD-100GHDT/GHPC/GHPCZBC/BD-142GHDT/GHPC/GHPCZ/GHPCD BC/BD-200GHDT/GHPC/GHPCZ/GHPCDBC/BD-98GHB BC/BD-138GHB BC/BD-198GHB·器具周围或在嵌入式结构里无阻碍物，保持通风通畅。
白雪828冰柜说明书
白雪828冰柜说明书定期清洁：冰柜使用时间长，难免会发出难闻的气味，甚至滋生细菌，影响食品原味。
因此，使用一段时间后，要把冰柜内的食物拿出来，替冰柜大搞一次卫生。
除了内部之外，冰柜外部如果“藏污纳垢”将影响散热，定期清洁也不能少，每年至少2次。
清洁注意：为避免冰柜受损，清洁冰柜时应先切断电源，用软布蘸上清水或食具洗洁精轻轻擦洗，然后蘸清水将洗洁精拭去，但不能用洗衣粉、去污粉、滑石粉、碱性洗涤剂、开水、油类、刷子等清洗冰箱，因为这些洗涤用品会损害箱外涂复层和柜内塑料零件。
柜内附件肮脏积垢时，应拆下用清水或洗洁精清洗，电器零件表面应用干布擦拭。
长时间不使用：应拔下电源插头，将箱内擦拭干净，待箱内充分干燥后，再将箱门关好,放置电冰箱的室内环境应通风良好、干燥、灰尘少，远离发热电器、炉具等热源，避免阳光直射。
电源电压：要符合白雪冰柜上所标注的额定电压，并要求在其波动范围内工作(一般小型电器电压在198-242V，大型设备据其功率而定)。
因为电压太低或太高极易损坏压缩机，从而造成不必要的损失，影响机器使用寿命。
清洗冷凝器：务必经常清洗冷凝器(一般每三个月清洗一次为佳)，因为冷凝器表面太脏容易导致制冷深度达不到设计要求，从而导致开机时间长。
这样不但费电而且也会影响机器的使用寿命。
温控器开关：机械型控温的白雪冰柜，不要把温控器开关放在强冷位置(一般调在3档为佳)。
数字温控型的白雪冰柜，则不要把温度设定得太低(一般冷藏温度设为5度为佳，冷冻温度设为-18度就可以了)。
否则，温度设得太低，让压缩机长时间工作的话，不但费电，也会影响机器的使用寿命。
轻搬轻放：搬动白雪冰柜要轻搬轻放，当师傅不在场时尽量不要让白雪冰柜与地面的倾斜度超过45度。
时刻保持白雪冰柜表面清洁卫生，使其不易腐蚀。
这样才能做到持久耐用。
厨王冰柜系列使用手册说明书
操作手册DHB系列保温柜产品识别有限保修兹保证本产品自安装之日起1年内或出厂之日起18个月内。
无材料和/或工艺上的缺陷。
经证明任何零部件存在材料和/或工艺上的缺陷，将由Prince Castle LLC决定进行免费更换或维修，顾客不需要承担零部件或人工服务费用。
本质保范围涵盖上门服务费（即路途费和/或里程费）。
计数里程上限为经授权的服务机构或其下属的服务机构来回路途（一次完成保修服务）100英里（200公里）。
本质保受以下例外/条件制约：•使用任何非Prince Castle的零配件将导致保修失效。
•本质保不涵盖超时费用或由非授权维修代理商或人员进行维修的部分。
•因粗心、疏忽和/或滥用（如坠落、篡改或修改零部件，运输途中造成的设备损坏，火灾，洪水或不可抗力）造成的损坏不属于本质保范围。
•由于使用不同于设备铭牌规定的电压而造成的所有问题不在本质保范围内，转换到正确的电压是客户的责任。
•在保修期内，此设备必须由Prince Castle的授权服务机构或Prince Castle 的服务技术人员进行维修。
目录产品识别 (1)安全信息 (2)安装 (2)操作 (3)清洗 (4)温度设定 (4)校准加热器 (4)编程 .................................................................................... 7-10 工厂预设 (11)问题解决 (12)接线图 (12)DHB2SS-20CN/DHB2PT-20CN解剖图及零件清单 (13)DHB2SS-33CN / DHB2PT- 33CN解剖图及零件清单 (14)PRINCE CASTLE标识按键LED 计时指示灯（三色）(数量，4，6或8) 上部盘菜单显示（数量2或3）BKFT早餐LED指示灯盘按键（数量4，6或8）上/下箭头按键菜单/确认按键REG(标准菜单)LED指示灯DHB2SS-20CN/DHB2PT-20CN DHB2SS-33CN/ DHB2PT-33CN温度控制面板电源开关食物盘和盘盖食物盘和盘盖时间条时间条电源开关温度控制面板警告 简要说明有关正确操作本机的重要信息。
东宝冰柜说明书
东宝冰柜说明书
1、在使用前用户要仔细阅读附带的产品说明书，检查冰柜的各个部件。
家用冰柜使用的电源多为220V，50Hz单相交流电源，正常工作时，电压波动允许在187-242V之间，如果波动很大或忽高忽低，将影响压缩机正常工作，甚至会烧毁压缩机。
2、冰箱应使用单相三孔插座，单独接线。
注意保护电源线绝缘层，不得重压电线，不得自行随意更改或加长电源线，没有接地装置的用户，应加装接地线，设置接地线时，不能用自来水和煤气管道做接地线，更不能接到电话线和避雷针上。
3、电冰箱使用的电源应为220伏、50赫兹单相交流电源，正常工作时，电源波动允许在187~242伏之间，如果波动很大或忽高忽低，将影响压缩机正常工作，甚至会燃烧压缩机。
4、开始使用时要减载运行，因为新机器的运动部件有一个磨合过程。
运转一段时间以后再加大量，这样能延长冰箱，冷柜的寿命。
5、使用冰箱时，存放的食物不能过多，要留有适当的空间，以保持冷气流通，尽量避免冰箱长时间满负荷工作。
热的食品要晾凉至室温后再放入，以免造成冰箱长时间不停机。
食品宜用保鲜袋或保鲜纸封好或放入密封容器中。